Rubi A230 PRO Manual Del Usuario página 12

12.
STARTING THE TOOL
WARNING! Check that the mains voltage is the same as that in the
machine's specifications.
Plug the machine in with the switch off. Starting the machine: Press
the lever 9 and pull the switch 8 simultaneously, until the latter
starts to operate. The switch 8 will block for continuous operation.
Stopping the machine: Pull the switch 8.
WORKING INSTRUCTIONS
For cutting or deburring, the part to be worked on must be secured,
unless it is heavy enough to remain in a stable position by itself.
For optimum performance and results when deburring, it
is advisable that the surface and the disc form an angle of
approximately 30º-40º. Guide the tool by pressing lightly forwards
and backwards. This prevents the part from overheating or
changing colour and the formation of striations.
WARNING! Never use a cutting disc for deburring. When cutting,
do not exert pressure on the disc. Do not tilt the machine. The disc
should not tilt or oscillate. Work with a steady speed, appropriate
for the type of material. When cutting, bear in mind the direction
of the work. Guide the machine against the direction of the cutting
tool, never in the opposite direction otherwise; there is a risk of the
machine veering off the cutting line uncontrollably. When cutting
profiles or rectangular section tubes, we recommend starting the
cut on the shortest side.
NOISE AND VIBRATION
This tool has been designed and made to reduce noise to a
minimum. However, in spite of this, in certain circumstances the
maximum noise level in the place of work could exceed 85
dBA. In this case, the operator should wear ear protection.
The machine's noise and vibration levels, measured in
compliance with EN60745.
Use ear protection!
WARNING! The vibration level given in these instructions has been
measured in accordance with a
procedure specified in EN60745 and can be used to compare
devices. Different uses of the device give rise to different vibration
levels and in many cases, they may exceed the values given
in these instructions. It is easy to underestimate the vibration
load if the electrical power tool is used regularly in particular
circumstances.
Note. If you wish to make an accurate assessment of the vibration
loads experienced during a particular period of working, you should
also take into account the intervening periods of time when the
device is switched off or is running but is not actually in use. This
can result in a much lower vibration load over the whole of the
period of working.
ACCESSORIES
Accessories and their corresponding order number can be found
in our catalogues.
MAINTENANCE AND CARE
WARNING! Always unplug the machine before carrying out work
on it.
English
ORIGINAL INSTRUCTIONS
standardized measurement
- Inspect the tool: Using a worn deburring or cutting tool will
diminish the efficiency of the work and could damage the
motor.
- Inspect the mounting screws: Regularly inspect all the
mounting screws and ensure they are firmly tight-ened.
Should any screw be loose, tighten it immediately. Failure
to do so could put you at serious risk.
- Motor maintenance: Always take the greatest care over
this and make sure that the motor winding is not damaged
and does not become wet with oil or water.
- The vents should always be kept clean and free of
obstacles.
- Clean the machine thoroughly after each use. Blast the
motor regularly with compressed air.
- Check that the mains lead is in good condition. If it is not,
take it to an Official Service Centre to have it replaced.
- Brush replacement: The brushes should be replaced after
150 - 200 hours use or when they are less than 10 mm
long. Have this done by an Official Service Centre. We
recommend that at every second change of brushes, you
take the machine to one of our Official Service Centres for
general cleaning and oiling.
- Use only RUBI accessories and spares. Parts the
changing of which is not covered in this instruction manual,
should be replaced in a RUBI.
After-sales service
Use only accessories and original spare parts supplied by
the manufacturer. Repairs should only be carried out by an
accredited workshop or RUBI technical support:
GERMANS BOADA SANTA OLIVA
Ronda de l'Albornar, 24-26
43710 Santa Oliva
Tarragona (Spain)
Tel: +34 977 16 90 50
WARRANTY
See general warranty conditions printed at the end of the
DISPOSAL
WARNING! Do not dispose of electric tools in the
household waste!
In accordance with European Directive 2012/96/EC relating to old
electrical and electronic appliances and its translation into national
law, used electric tools must be collected separately and recycled
in an ecologically desirable way.
Without the previous authorisation of GERMANS BOADA S.A.,
the partial or total reproduction of this manual, in any format or
by any means or process, is strictly prohibited, whether such
reproduction be mechanical, photographic or electronic.
Any of these activities will incur legal liability and may give rise to
penal action being taken.
GERMANS BOADA S. A. reserves the right to make any technical
modification without previous notice.
manual