Technical Specifications - Stanley STHT77149 Manual De Instrucciones

• Align the circular pocket on the back of the laser with the magnetic circle on the front of the wall
attachment.
• Make sure that the unit is seated firmly, and is secure on the wall.
CAUTION: Pin is sharp and should be handled with care. Always be sure drywall pin is closed when
not in use.
NOTE: The pin is only for use on drywall NOT other surfaces including plaster.
Operating Instructions
DANGER: Laser Radiation, avoid direct eye exposure.
ON/OFF ACTUATOR - FIGURE E
• Slide the ON/OFF actuator (1) to the middle position shown in Figure E to turn the laser on in a
locked position.
• Slide the actuator all the way to the right to activate the self leveling mode.
• Slide the actuator all the way to the left to turn the laser off.
PROTRACTOR MODE
The internal protractor (2) (Figure B) of the laser can be used to:
• Transfer an angle
• Apply an angle (Example : transfer stair angle to align pictures on stairs wall)
USING THE PROTRACTOR - FIGURE F, G
• Hang the laser on the wall surface using one of the 2 different hanging modes or hand hold it on the
wall.
• Slide the on/off actuator (1) to the middle position.
• The laser will come on and project a laser line.
• It will be locked in one position.
• The protractor (2) back light will come on.
• The protractor window will show an angle relative to vertical.
• The unit can be spun around 360 degrees, and the angle reading can be taken from the window.
• The angle can then be transferred to another work area.
• Although the laser direction can be changed from vertical to left or right in "Protractor Mode", for
best results, it should be set to the vertical position.
AUTO LEVELING MODE - FIGURE H,I,J,K,L
To activate the Self Leveling Mode, slide the ON/ OFF actuator (1) all the way to the right.
• The protractor window backlight will go out.
• The laser will project a "plumb" line vertically. (Figure H)
DIRECTING THE LASER LINE - FIGURE I,J,K
The laser can be projected level to the left, plumb (straight up) and level to the right.
• The buttons on the sides (3 & 4) are used to change the direction of the laser line.
• To change the direction, push the button in the direction you want the laser to go.
• In figure J the button is fully depressed, and a level laser line is directed out the left side of the unit.
• Press button the other way, and the laser line directs out the right side of the unit.
• With the button pushed back to center, the laser line is projected vertically.
STORAGE
Always store the laser indoors with the ON/OFF actuator (1) in the "OFF" position.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never
immerse any part of the tool into a liquid.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other
than those listed in this manual) should be performed by authorized service centers or other qualified
service personnel, always using identical replacement parts.
Accessories
WARNING: The use of any accessory not recommended for use with this tool could be hazardous.
WARRANTY
Two Year Warranty
Stanley warrants its electronic measuring tools against deficiencies in materials and / or workmanship for
two years from date of purchase.
Deficient products will be repaired or replaced, at Stanley's option, if sent together with proof of purchase
to:
Stanley UK Sales Limited
Gowerton Road
Brackmills, Northampton NN4 7BW
This Warranty does not cover deficiencies caused by accidental damage, wear and tear, use other than in
accordance with the manufacturer's instructions or repair or alteration of this product not authorised by
Stanley.
Repair or replacement under this Warranty does not affect the expiry date of the Warranty.
To the extent permitted by law, Stanley shall not be liable under this Warranty for indirect or
consequential loss resulting from deficiencies in this product.
This Warranty may not be varied without the authorisation of Stanley.
This Warranty does not affect the statutory rights of consumer purchasers of this product.
This Warranty shall be governed by and construed in accordance with the laws of the country sold where
in and Stanley and the purchaser each irrevocably agrees to submit to the exclusive jurisdiction of the
courts of that country over any claim or matter arising under or in connection with this Warranty.
Calibration and care are not covered by warranty.
NOTE: The customer is responsible for the correct use and care of the instrument. Moreover, the customer
is completely responsible for periodically checking the accuracy of the laser unit, and therefore for the
calibration of the instrument.
Subject to change without notice
.

TECHNICAL SPECIFICATIONS

Laser Diode Wavelength:
Laser Class:
Working Range:
conditions)
Leveling Accuracy:
Auto Leveling Range:
Auto Leveling Lines Settling Time:
Batteries:
Voltage:
Operating Temperature:
Complies with 21 CFR 1040.10 and 1040.11 except for deviations pursuant to Laser Notice No. 50,
dated June 24, 2007
630 - 680 nm (red color)
Class 2
Up to 20 feet (609 cm) (depends on light
±1/8 inch (3 mm) @ 10 feet (3 m)
±2.5°
≤8 sec
2 AAA batteries (included)
3.0 Volt
41°F (5°C) - 104° F (40°C)