Stanley Jumpit J5C09 Manual De Instrucciones página 4

• Continue to charge for one to two more hours.
• Once fully charged disconnect the AC charging adapter from the mains power socket and then remove the jack plug
of AC charging adapter from the 12V AC/DC charging socket on the back of the unit. Store it in a safe place.
CHARGING THE UNIT USING THE 12 VDC CHARGING ADAPTER
Charging the unit from an external 12 VDC power source requires the use of the 12 VDC charging adapter. This
adapter has a male dc connector at each end.
• Insert the gold-tipped plug of the 12 VDC charging adapter into the accessory socket socket of your vehicle or other
12 VDC power source.
• Insert the silver-tipped plug into the 12 VDC accessory socket on the front panel of the unit.
• Charge the unit until the green (full) battery status LED lights when the battery power level button is pressed (AFTER
unplugging the adapter from the unit).
• When charging is complete, disconnect the 12 VDC charging adapter and store it in a safe place.
note:
Some vehicles require that the ignition be switched to the accessory socket position in order to power the accessory socket.
caution! to reduce the risk of property damage:
• Recharge using this method only when necessary. Frequent use the the 12 volt DC charging method may shorten
battery life.
• Do not charge for longer than 6 hours maximum using this method and do not leave the unit unattended when
charging using this method.
using the unit as a jump-starter
WARning: Make sure that the vehicle is in neutral with the parking brake applied.
note:
If your connections are incorrectly made, the unit will beep continuously and the red reverse polarity indicator will illuminate, even if
the on/off switch is in the off position. Rectify the connections immediately.
WARning: Make sure that the cables are not in the path of moving belts or the fan.
1. Turn off the vehicles ignition and all accessories before making any connections.
2. Make sure that the jump-starter on/off switch is turned off.
3. The following procedure is for a negative earth system ie the negative battery terminal is connected to the chassis.
4. Connect the positive (+) red clamp to the vehicle's positive battery terminal.
5. Connect the negative (–) black clamp to chassis or a solid, non-moving, metal vehicle component or chassis part.
Never clamp directly to negative battery terminal or moving part. Refer to the automobile owner's manual.
6. Turn the jump-starter on/off switch to the on position.
7. Start the vehicle and crank the engine in 3 to 6 second bursts.
important! If the engine doesn't start within 6 seconds let the units internal battery cool for 3 minutes before
making another attempt.
8. When the vehicle starts, turn the jump-starter off/on switch to the off position.
9. Leave the vehicle's engine running.
10. Disconnect the (–) black clamp connected to the engine or chassis first, followed by the (+) red clamp that is
connected to the battery positive (+) terminal.
11. Carefully press the negative (black) jumper cable wire into the storage channel starting at the end furthest from the
clamp.
12. Clamp the negative (black) clamp onto the clamp holder.
13. Carefully press the positive (red) jumper cable wire into the storage channel starting at the end furthest from the
clamp.
14. Clamp the positive (red) clamp onto the clamp holder.
15. Charge the unit as soon as possible.
16. Make sure that the jump-starter on/off switch is turned off while the unit is being charged or stored.
using the compressor
WARning: When using the compressor:
• Do not use the compressor when the charger is connected to the mains.
• Do not direct the nozzle at animals or bystanders.
• Never leave the compressor unattended when running.
• Only use the adapters supplied.
• Should the unit run over an extended period of time it may overheat and cause the thermal trip to activate. When this
occurs switch the compressor off and allow to cool for 30 minutes.
• Keep the compressor stored out of reach of small children.
• The gauge is intended as a guide only. Tyre pressures should be regularly checked with a certified gauge.
• Do not over inflate any object as this may cause a risk of injury.
this compressor can be used to inflate car tyres and sports equipment.
EnglisH
J5C09EU_Manual_040512.indd 6-7
6
• Remove the compressor hose from the storage compartment.
• If an adapter is required, choose the correct adapter for the product you are inflating and fit it into the nozzle.
• Fit the nozzle of the compressor or the adapter, if fitted, to the valve of the item to be inflated. Make sure that the
nozzle is locked in place.
• Move the compressor switch to the on position.
• Monitor the pressure gauge until the required pressure is reached.
• Move the compressor switch to the off position.
• Remove the adapter, if fitted, or the nozzle from the inflated item.
• Remove the adapter, if fitted, and store it in the compressor nozzle storage compartment.
using the pivoting led area light
The pivoting area light is controlled by the area light power switch on top of the light. Make sure the area light is turned
off when the unit is being recharged or stored.
using the usB socket
1. Push the USB power button to turn the USB port on. The USB power indicator will light.
2. Lift up the cover of the USB socket.
3. Plug the USB-powered device into the USB socket and operate normally.
notes:
This unit's USB socket does not support data communication. It only provides 5 volts/500mA DC power to an external USB-powered
device.
Make sure the USB power button is in the off position when the unit is being recharged or stored.
Some household USB-powered electronics will not operate with this unit.
using the 12 volt dc power socket
This portable power source is also for use with all 12 volt dc accessories equipped with a male accessory socket plug
and are rated up to 5 amps.
1. Lift up the cover of the unit 's 12 VDC socket.
2. Insert the 12 volt dc plug from the appliance into the 12 VDC accessory socket on the unit. DO NOT EXCEED A 5
AMP LOAD.
3. Switch on the appliance and operate as usual.
4. Periodically press the battery power level button to check battery status.
trouBleshootIng
unit will not charge
• Make sure the power switch is in the off position.
• Make sure the jack of the mains charging adapter is properly connected to both the unit and a functioning mains
power socket.
• Make sure the 12 VDC charging adapter is properly connected to both the unit and the accessory socket socket of
your vehicle or other 12 VDC power source.
unit Fails to Jump-start
• Make sure unit's power switch is in the on position.
• Check that jump-starter has a full charge. Recharge unit if necessary.
•
Make sure a proper polarity cable connection has been established.
Portable compressor will not inflate
• Make sure the compressor power switch is in the on position.
• Check that unit has a full charge. Recharge unit if necessary.
• Make sure connector is pushed to valve stem and thumb latch is closed when attempting to inflate tires; or nozzle
(adapter) is securely inserted into connector (chuck) on all other inflatables.
usB Power Port will not power appliance
•
Make sure the USB charging port power button is in the on position.
•
Check that unit has a full charge. Recharge unit if necessary.
lED Area light does not come on
• Make sure the Pivoting LED area light power switch is in the on position
• Check that unit has a full charge. Recharge unit if necessary.
12 volt Dc accessory outlet will not power appliance
• Make sure the the appliance does not draw more than 5 amps.
• Check that unit has a full charge. Recharge unit if necessary.
or
7 EnglisHn
4/5/2012 7:56:26 PM