Vacuum Mode; Battery Power - DeWalt DCV584L Traducido De Las Instrucciones Originales

2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. C)
Some D WALT battery packs include a fuel gauge which
e
consists of three green LED lights that indicate the level of
charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 14 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end-user application.
Connecting the Hose (Fig. D)

Vacuum Mode

1. Insert the notched connecting piece
inlet 4 .
2. Turn the connecting piece clockwise to fix the hose
into position.
3. Connect the appropriate accessory to the hose nozzle
Blow Mode
1. Insert the notched connecting piece
outlet 5 .
2. Turn the connecting piece clockwise to fix the hose
into position.
3. Connect the appropriate accessory to the hose nozzle
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING : To reduce the risk of serious personal
injury, turn appliance off and disconnect appliance
from power source and remove battery pack before
making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
Switching On and Off (Fig. A)
To switch the appliance on, set the on/off switch
To switch the appliance off, set the on/off switch
position O.
Power Source
This vacuum runs either on mains power or battery power.
The vacuum will switch between AC (mains) and DC (battery)
power automatically.
Mains Power
1. Fully unwind the mains cable.
2. Connect the plug to the mains outlet before turning the
appliance on.
•
•

Battery Power

1. Tidy the mains cable.
2. Insert a battery pack
3. Make sure the battery pack is properly seated.
nOTE: The mains cable power source is only designed to power
the operation of the vacuum and will not charge an installed
battery pack.
Vacuuming (Fig. A, E, F)
1. Empty and clean the tank
2. Connect the notched connecting piece
3. Select the appropriate accessory.
nOTE: We recommend not mixing wet and dry substances.
When switching substances, empty and clean the tank first.
into the vacuum
15
Dust Collection (Fig. E)
In the vacuum mode, your D
dust collector for applications producing dust or debris.
Your D
11 .
connection system. This system allows for a fast, secure
connection between the suction hose
15 into the blow
AirLock connector
tools or through the use of the included AirLock adapter
nOTE: When using an adapter ensure it is firmly attached to the
tool outlet before following the steps below.
11 . 1. Ensure the collar on the AirLock connector is in the unlock
2. Push the AirLock connector onto the adapter
3. Rotate the collar to the locked position.
Wet/Dry Filter (Fig. F)


1 to position I.
to
1


Always turn the vacuum off when work is finished and
before unplugging.
Tidy the mains cable when the vacuum is not in use.
.
13
before use.
3
inlet 4 .
WALT vacuum can function as a
e
WALT vacuum is fitted with the D
e
connects directly to D
11
position. Align notches on collar and AirLock connector as
shown for unlock and lock positions.
connector point.
nOTE: The ball bearings inside collar lock into slot and
secure the connection.The power tool is now securely
connected to the dust extractor.
WARNING : Always operate the appliance with the
dust filter 16 in place.
WARNING : Always use the appliance in upright
position. Do not tilt the appliance, in order to
prevent liquids collected in the tank from entering
the motor housing.
WARNING: If foam or liquid escapes from the machine,
switch off immediately.
CAUTION: Clean the water level limiting device regularly
and examine it for signs of damage.
EnGLIsh
15 to the vacuum
WALT AirLock
e
9 and a power tool. The
WALT compatible
e
12 .
33