swissflex UNI 20-85RF Manual De Instrucciones página 22

22_85RF bridge
with care; do not disassemble or
modify them, do not allow children
to play with them and prevent frail
individuals from using the product
without supervision.
The product may not be used with a
medical device or be installed in a
medical device.
The product may not be used in an
environment in which flammable
or explosive gases or vapours (e.g.
anaesthetics) are likely to occur.
The product may not be used to
raise and lower loads.
Only use spare parts that have been
produced or approved by Swissflex.
Only these parts guarantee ade-
quate safety.
The slat base may only be used
with the power supply provided.
Initial setup «Touch»
Place the batteries into the radio remote control
Remove the cover from the battery compartment (21)
on the back of the radio remote control. Place 3 AAA-
batteries (22) into the compartment, paying attention
to the +/- markings. Close the compartment cover
again. The maximum range of the radio remote control
is 15 metres.
Teaching-in the radio remote control (already
taught-in in the factory)
1. Remove the radio remote control's battery cover on
the back of the device.
2. Insert / check the batteries (3 x AAA).
3. Activate the teach-in button (30) on the switching
power supply (press 2 x).
4. A small red button is located above the batteries in
the battery compartment of the device (21).
5. Press the button; a blue LED will start flashing.
6. Hold the button down until the blue LED is perma-
nently illuminated; this means that pairing has been
completed.
22
Operating instructions
®
and accessories
Bluetooth ®
1. Download the standard „Swissflex" app from the
relevant platform for Android (Google play) or Apple
iOs (App Store).
2. Install the standard „Swissflex" app onto your
Smartphone / Tablet PC.
3. Installation / Initial setup, see manual of the Blue-
tooth RF-Gateway.
Synchro function (with sync cable)
When two uni 20_85RF/uni 22_85RF bridge
together with a sync cable (connection jack (23)), the
synchro function (17) is required. By pressing and
holding down the button (17), the synchro function is
activated/deactivated. When pressing the travel button
(6-7), the control systems synchronise and then move
in the confirmed direction of travel. After successful
activation, the button glows blue continuously. After
successful deactivation, the button appears white. Af-
ter plugging in the sync cable, carry out a reset as
follows:
• Press down the 'Memory/Save' button (18) for 3 se-
conds.
• The M1-M4 buttons will first light up blue and then
switch to white again.
• The LCD backlighting system will flash white once
after several seconds.
• Immediately press down the synchro button (17)
and keep it pressed down. The control systems po-
wer down.
• If the entire backlighting system flashes white twice,
you can release the synchro button (17).
The internal meter readings for the individual motors
have now been reset to '0' and the sync function can
work correctly.
Under-floor lighting
Activate the under-floor lighting by pushing the „Un-
der-floor lighting" button (8). This switches off auto-
matically after 30 minutes, or if the button is pushed
once again. This button is illuminated (blue) when it is
pushed.
Pocket lamp
The pocket lamp is illuminated when the „Pocket lamp"
button (5) is held down. The light turns off when the
button is released. This button is illuminated (blue)
while the pocket lamp is in use.
Lock buttons
To lock the buttons, hold down the „Lock buttons" but-
ton (20) for five seconds. Once the button lock has been
activated, all buttons (except for the mains outlet (19),
the pocket lamp (5), the under-floor lighting (8) and
the button lock (20)) flash (blue) twice.
All buttons flash twice (white) when a disabled button
® are linked
Af-
EN