MAG TOOLS BWP152 Manual De Instrucciones página 12

English
Anvil with Hog Ring (Fig. A)

WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that it con tains no cracks.

CAUTION: Inspect anvils and hog rings prior to
use. Missing or damaged items should be replaced
before use.

CAUTION: Place the switch in the locked off
(center) position and remove battery pack before
changing accessories.
To install an accessory on the hog ring anvil, firmly push
3
accessory onto the anvil . The hog ring
to allow the accessory to slide on. After the accessory is
installed, the hog ring applies pressure to help provide
accessory retention.
To remove an accessory, grasp the socket and firmly pull
it off.
Operating the Wrench

CAUTION: Ensure fastener and/or system will
withstand the level of torque generated by the tool.
Excessive torque may cause breakage and possible
personal injury.
1. Place the socket on the fastener head. Keep the tool
pointed straight at the fastener.
2. Press switch to start operation. Always check torque
with a torque wrench, as the fastening torque is affected
by many factors including the following:
Voltage: Low voltage, due to a nearly discharged
-
battery, will reduce fastening torque.
socket size: Failure to use the correct socket size
-
will cause a reduction in fastening torque.
Bolt size: Larger bolt diameters generally
-
require higher fastening torque. Fastening torque
will also vary according to length, grade, and
torque coefficient.
Bolt: Ensure that all threads are free of rust and
-
other debris to allow proper fastening torque.
Material: The type of material and surface finish of
-
the material will affect fastening torque.
Fastening Time: Longer fasten ing time results in
-
increased fastening torque. Using a longer fastening
time than recom mended could cause the fasteners
to be overstressed, stripped or damaged.
10
Square Drive
Max breakaway torque
Noise Level
Pressure
Power
Vibration
Blow rate
Free speed
Weight
8
compresses
MAINTENANCE

Your Mac Tools power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning.
Cleaning


Accessories



Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact
Mac Tools, 505 North Cleveland Ave., Suite 200, Westerville,
Ohio 43082, call 1–800-MAC-Tools (1–800–622–8665), or
visit our website www.mactools.com.
SPECIFICATIONS
BWP152
ft-lbs / Nm
dB(A)
dB(A)
m/s
2
bpm
rpm
lbs / kg
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/
installing attachments or accessories. An
accidental start-up can cause injury.
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non-metallic parts of
the tool. These chemicals may weaken the plastic
materials used in these parts. Use a cloth dampened
only with water and mild soap. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
WARNING: Since accessories, other than those
offered by Mac Tools, have not been tested with this
product, use of such accessories with this tool could
be hazardous. To reduce the risk of injury, only Mac
Tools recommended accessories should be used with
this product.
WARNING: To reduce the risk of injury, use only Mac
Tools impact-ready accessories.
WARNING: Use only impact accessories. Non-impact
accessories may break and cause a hazardous
condition. Inspect accessories prior to use to ensure
that they con tain no cracks.
1/2"
1200 / 1627
104 / 3
115 / 3
13 / 5.9
2400
400 / 1900 / 1900
5.8/2.6