Power Supply; Settings Menu - Rollei Soluna 300 Pro Manual

8

Power supply

• Use with power cord: Insert the mains cable supplied into the
mains cable socket of the control box. Connect the light head to
the control box using the cable supplied.
Press the on/off switch on the control box for about 2 seconds
to switch the control box and the light head on or off. If the
unit is in sleep mode, you can reactivate it by briefly pressing
the on/off switch.
• Use with rechargeable V-Mount battery packs: Connect the bat-
tery pack(s) (not supplied) to the control box via the connector
provided and press the on/off switch for approx. 2 seconds to
switch the LED light on. For battery operation we recommend
V-Mount batteries with an energy of at least 190 Wh (Soluna
300 Pro) or 250 Wh (Soluna 500 Pro).
Compatibility of accessories:
• The LED permanent light is equipped with an umbrella holder
on the lighting head for reflex/transmitted light umbrellas and
the Bowens S-type bayonet for the use of various light shapers
(softboxes, reflectors, beauty dishes, etc.)
• Insert the light shaper with the three bayonet pins into the
corresponding recesses on the LED lighting head and lock it by
turning it briefly to the right until it audibly clicks into place.
Brightness
Adjust the brightness:
• After power on, turn the adjustment knob clockwise to increase
the brightness and counterclockwise to decrease the brightness.
• The brightness can be adjusted between 0% and 100% in 1%
increments.
Lighting effects
You can use the LED permanent light to create various lighting
effects. To do this, briefly press the light effect mode button to
access the effects. By briefly pressing the light effect mode button
again, you can now choose between the different modes:
1: TV flicker
2: Flickering light bulb
3: Fireworks
4: Thunderstorm mode
5: Flashing mode
After selecting the desired lighting effect, briefly press the adjust-
ment knob to set the effect. Press once to access the brightness
setting, press again to access the frequency setting. By turning the
setting knob at a time, you can adjust the brightness between
0 – 100% and the frequency between 1 – 10. 1 describes the slo-
west and 10 the fastest frequency.
• Modes 1 and 2 run continuously, modes 3, 4 and 5 play short
light sequences. To start them, briefly press the lighting effect
start button.
• To switch off the lighting effects, press the return button.
ENGLISH
• To remove the light shaper, pull the bayonet release button to
the rear, turn the light shaper to the left and pull it off to the
front.
U-bracket:

Settings menu

• Press the radio signal and light effect mode buttons simulta-
neously to enter the settings menu.
• Briefly press the setting button to scroll through the options.
When an option is selected, the icon turns green. Turn the set-
ting knob to select the setting, confirm by briefly pressing the
setting knob and press the return key to return to the menu.
The settings menu contains the following options:
Cooling
• You can switch the cooling system of the LED light on or off.
To do this, go to the settings menu and switch off the cooling
system via the first setting point. The symbol in the display
indicates whether the cooling system is switched on or off.
• Please note that when the cooling system is switched off, the
LED light can only be operated at a maximum output of 30% to
protect it from overheating. This reduced power is nevertheless
indicated as 100% power.
To enable the LED light to also
be mounted from above (e.g.
on the ceiling), the unit is
attached using the useful
U bracket. You can loosen the
knobs on the sides, turn the
bracket around and mount it
again from above. This ensures
that the heat is still reliably
dissipated.
• Cooling: Auto / On / Off
• Communication: Radio signal
over 2.4 GHz / Bluetooth* /
DMX
• Reset Bluetooth*:
Yes / No
• Factory settings:
Yes / No