GGP ITALY MT48Li Manual De Instrucciones página 71

moved from right to left.
■ Use the tip of the cutting line to do the cutting; do not
force cutting head into uncut grass.
■ Wire and picket fences cause extra cutting line wear,
even breakage. Stone and brick walls, curbs, and
wood may wear cutting line rapidly.
■ Avoid trees and shrubs. Tree bark, wood moldings,
siding, and fence posts can easily be damaged by the
cutting line.
ADVANCING CUTTING LINE
NOTE: The trimmer is equipped with an auto-feed head.
Bumping the head to try to advance the line will damage
the trimmer and void the warranty.
■ With the trimmer running, release the switch trigger.
■ Wait two seconds, and press the switch trigger.
NOTE: The cutting line will extend approximately
0.635cmwith each stop and start of the trigger until the
cutting line reaches the length of the grass deflector cut-
off blade.
■ Resume trimming.
ADVANCING CUTTING LINE MANUALLY See Figure
7.
■ Remove the battery pack.
■ Push the black button located on the cutting head
while pulling on cutting line to manually advance the
cutting line.
■ ■ After extending new cutter line, always return
the machine to its normal operating position before
switching on.
ADJUSTABLE CUTTING DIAMETER See Figure 9.
■ Rotate the plant protector to its working position to
avoid cutting flowers or plants by mistake.
■ Remove the battery pack.
■ Adjust the "cutting diameter slide" on the grass
deflector to adjust the cutting path diameter. There
are 2 diameter options: 30cm, 25cm.
NOTE: a small diameter cutting pathe will maximize run
time and cutting speed, while a larger cutting pathe will
help complete the trimming task quicker.
LINE CUT-OFF BLADE See Figure 10.
This trimmer is equipped with a line cut-off blade on the
grass deflector. For best cutting, advance line until it is
trimmed to length by the line cut-off blade. Advance line
whenever you hear the engine running faster than
normal, or when trimming efficiency diminishes. This will
maintain best performance and keep line long enough to
advance properly.
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING
To avoid serious personal injury, always remove the
battery pack from the tool when cleaning or
performing any maintenance.
Before each use, inspect the entire product for
damaged, missing, or loose parts such as screws, nuts,
bolts, caps, etc. Tighten securely all fasteners and caps
and do not operate this product until all missing or
damaged parts are replaced.
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use.
Use clean cloths to remove dirt, dust, oil, grease, etc.
Do not at any time let brake fluids,gasoline,
petroleum-based products, penetrating oils, ect.come
in contact with plastic parts. Chemicals can damage,
weaken or destroy plastic which may result in seriou
personal injury.
Only the parts shown on the parts list are intended to
be repaired or replaced by the customer. All other parts
should be replaced at an Authorised Service Centre.
Upon removal, cover the battery pack's terminals with
heavy-duty adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove any of its
components. Lithium-ion and nickel-cadmium
batteries must be recycled or disposed of properly.
Also, never touch both terminals with metal objects
and/or body parts as short circuit may result. Keep
away from children. Failure to comply with whese
warning s could result in fire and.or serious injury.
SPOOL REPLACEMENT See Figure 12.
Use original manufacturer's replacement cutting line for
best performance.
■ Remove the battery pack.
■ Push in tabs on side of spool cover.
■ Pull spool cover up to remove.
■ Remove the old spool.
■ To install the new spool, make sure the cutting line
is captured in the slot on the new spool. Make sure
the end of the cutting line is extended approximately
15cm beyond the slot.
■ Install the new spool so that the cutting line and slot
align with the eyelet in the cutting head. Thread the
cutting line into the eyelet.
■ Pull the cutting line extending from the cutting head
so the cutting line releases from the slot in the spool.
■ Reinstall the spool cover by depressing tabs into
slots and pushing down until spool cover clicks into
place.
CUTTING LINE REPLACEMENT See Figures 12 - 13.
■ Remove the battery pack.
EN
WARNING
WARNING
WARNING
6