Lutron D-600P Manual De Instrucciones

Incandescent / Halogen 120 V
English
Dimmer
P/N 030-892
Rated at 120 V~ 60 Hz
Important Notes
Please read before installing.
1. CAUTION: Use only with permanently-installed 120 V incandescent or halogen
fixtures. To avoid overheating and possible damage to other equipment, do not use
to control receptacles, fluorescent lighting fixtures, motor-driven appliances, or
transformer-supplied appliances.
2. Install in accordance with all national and local electrical codes.
3. Only one dimmer can be used in a 3-way circuit.
4. When no "grounding means" exist within the wallbox then NEC
allows a dimmer without a grounding connection to be installed as a replacement,
as long as a plastic, noncombustible wallplate is used. For this type of installation,
cap or remove the green ground wire on the dimmer and use an appropriate
wallplate such as Lutron's Claro or Fassada series wallplates.
® TM
5. For new installations, install a test switch before installing the dimmer.
6. Protect dimmer from dust and dirt when painting or spackling.
7. Recommended minimum load is 40 Watts
8. It is normal for the dimmer to feel warm to the touch during operation.
9. Clean dimmer with a soft damp cloth only . Do not use any chemical cleaners.
Multigang Installations
When installing more than one control in the same wallbox, it may
be necessary to remove all inner side sections prior to wiring (see
diagram). If pre-installed, remove the Lutron wallplate and
wallplate adapter from dimmer. Using pliers, bend side section up
and down until it breaks off. Repeat for each side section to be
removed. Removal of dimmer side sections reduces maximum
load capacity. Refer to chart below for maximum dimmer
capacity.
Dimmer Capacity Chart
Dimmer No sides
Rating removed
600 W 600 W max.
1000 W 1000 W max.
Technical Assistance
?
If you have questions concerning the installation or operation of this product, call the Lutron
Technical Support Center . Please provide exact model number when calling.
U.S.A. and Canada (24 hrs/7days)
+1-800-523-9466
Other countries 8am – 8pm ET
+1-610-282-3800
Limited Warranty
(Valid only in U.S.A., Canada, Puerto Rico, and the Caribbean.)
Lutron will, at its option, repair or replace any unit that is defective in materials or manufacture within one year after purchase. For warranty service,
return unit to place of purchase or mail to Lutron at 7200 Suter Rd., Coopersburg, PA 18036-1299, postage pre-paid.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES, AND THE IMPLIED WARRANTY OF MERCHANTABILITY IS
LIMITED TO ONE YEAR FROM PURCHASE. THIS WARRANTY DOES NOT COVER THE COST OF INSTALLATION, REMOVAL OR
REINSTALLATION, OR DAMAGE RESULTING FROM MISUSE, ABUSE, OR DAMAGE FROM IMPROPER WIRING OR INSTALLATION.
THIS WARRANTY DOES NOT COVER INCIDENTAL OR CONSEQUENTIAL DAMAGES. LUTRON'S LIABILITY ON ANY CLAIM FOR
DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE MANUFACTURE, SALE, INSTALLATION, DELIVERY, OR USE OF THE UNIT
SHALL NEVER EXCEED THE PURCHASE PRICE OF THE UNIT.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages, or limitation on how long an implied warranty may last, so the above limitations may not apply
to you.
This product may be covered by one or more of the following U.S. patents: 4,835,343; 4,835,816; 4,939,383; 4,947,054; 5,262,678;
5,359,231; 5,637,930; D335,282; D 342,234; and corresponding foreign patents. Lutron, Claro, and Glyder are registered trademarks and
Fassada is a trademark of Lutron Electronics Co., Inc. NEC is a registered trademark of the National Fire Protection Association, Quincy,
Massachusetts.
© 2006 Lutron Electronics Co., Inc.
Lutron Technical Support Center
Models:
600 W 1000 W
D-600P AY-10P
D-600R AY-10PNL
D-603P AY-103P
DNG-600P AY-103PNL
DNG-603P GL-10P
GL-600 GL-1000
GL-600P GL-103P
2002, Article 404-9
GL-603P S-10P
®
LG-600P S-10PNL
LG-603P S-1000
S-600 S-103P
S-600P S-103PNL
S-600PNL TG-10P
S-603P TG-10PNL
S-603PNL TG-103P
SW-600
SW-600P
SW-603P
Do Not Remove
Outside Sections
Each Control Has Inside Middle Control Has Two
Sections Removed Side Sections Removed
1 side 2 sides
removed removed
500 W max. 400 W max.
800 W max. 650 W max.
Fax +1-610-282-6311
http://www.lutron.com
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Made and printed in U.S.A. 2/06 P/N 030-892 Rev. A
1-800-523-9466
Installation
1
Turning OFF Power.
• Turn power OFF at circuit breaker (or remove fuse).
2
Removing Wallplate and Switch.
• Remove wallplate and switch mounting screws.
• Carefully remove switch from wall (do not remove wires).
Caution: Verify power
is OFF to switch
before proceeding.
3
Identifying the Type of Circuit.
Different-colored screw
(Common). Actual location may
vary.
OR
Ground (Bare
Copper or
Green Wire)
Ground (Bare Copper
or Green Wire)
SINGLE-POLE: 3-WAY:
Insulated wires connected Insulated wires connected to three screws. One of
to two screws of the same these wires is connected to a screw of a different-
OR
color. Replace with a color (not green) or labeled COMMON. MARK or
SINGLE-POLE dimmer. TAG this wire to identify it when wiring. Replace
See Step 5a. with a 3-WAY dimmer. See Step 5b.
4
Disconnecting Switch Wires.
Important Note: Your wall switch may have two wires attached to the same screw (see
illustrations below for examples). Tape these two wires together before disconnecting.
Connect both wires to the dimmer wire in Step 5.
One wire in the
backwired hole
and one to the
screw.
Screw Terminals: Push-in Terminals:
Turn screws to loosen. Insert screwdriver. Pull
wire out.
24 hrs / 7 days www.lutron.com
5
Wiring the Dimmer.
• For installations involving more than one control in a wallbox, refer to the
section on Multigang Installations before beginning.
Note: Wire location will vary by product. Reference wires by color, not location.
5a - Single-Pole Wiring
Black
Ground
Green
Black Black
120 V~
Green
60 Hz
120 V
60 Hz Light
Ground
5b - 3-Way Wiring
Tag
Black
Tag
Green
Red
Black Red
120 V~
Green Red
60 Hz
Dimmer 3-Way Switch
120 V
60 Hz Ground
6
Mounting Dimmer to Wallbox.
• Form wires carefully into the wallbox, mount and
align dimmer.
One continuous
wire to the • Install wallplate.
screw.
Start screws.
7
Turning ON Power.
• Turn power ON at circuit breaker (or replace fuse).
Looped Wire:
Turn screw to loosen.
• Connect the green dimmer ground wire
to the bare copper or green ground wire
in the wallbox. (See Important Note 4.)
• Connect one of the black dimmer wires
to either of the wires removed from the
switch.
• Connect the remaining black dimmer
wire to the other wire removed from the
switch.
Note: To use a 3-Way dimmer (one
black and two red wires) in a single-pole
application, cap off one of the red wires
and follow instructions for single-pole
wiring. (If the on/off switch works
backwards, switch the red wires.)
• NOTE: Only one dimmer can be used in
a 3-WAY circuit.
• Connect the green dimmer ground wire
to the bare copper or green ground wire
in the wallbox. (See Important Note 4.)
• Connect the black dimmer wire to the
wire removed from the different-colored
screw on the switch (marked or tagged
wire). Remove tag from wire.
• Connect one of the red dimmer wires to
Ground either of the remaining wires removed
from the switch.
• Connect the remaining red dimmer wire
to the remaining wire removed from the
switch.
Light
Note: To install a
traditional style
wallplate, firmly pull the
Glyder or Rotary knob
®
to remove it. Install the
wallplate and re-attach
the knob.
Glyder
®
Align dimmer and
tighten screws.
Rotary