Advance Carpetriever 28 Instrucciones De Uso página 8

ENGLISH
INTRODUCTION
This manual will help you get the most from your Advance
Carpetriever™ 28. Read it thoroughly before operating the machine.
Note: Bold numbers in parentheses indicate an item illustrated on
page 2 (fi gure A).
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized
Advance Service Center, who employs factory trained service personnel,
and maintains an inventory of Advance original replacement parts and
accessories.
Call the ADVANCE DEALER named below for repairs, parts or service.
Please specify the Model and Serial number when discussing your
machine.
(Dealer, affi x service sticker here.)
NAME PLATE
The Model Number and Serial Number of your machine are shown on
the Nameplate on the machine. This information is needed when ordering
repair parts for the machine. Use the space below to note the Model
Number and Serial Number of your machine for future reference.
MODEL NUMBER ____________________________________
SERIAL NUMBER ____________________________________
UNCRATING
When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton
so that it can be inspected. Contact the Advance Customer Service
Department immediately to fi le a freight damage claim.
A - KNOW YOUR MACHINE
1 Power Cord
2 Bag Housing Door
3 Brush Height Adjustment Knob
4 Wand
5 Main Power Switch
6 Trigger Bar
7a Wand Control Lever (Before June 2005)
7b Wand Control Lever (After May 2005)
8 Circuit Breaker
9 Hand Grips
8 - FORM NO. 56041467 - Carpetriever
INSTALLING A FILTER BAG
1 Open the Bag Housing Door (2) and install either a Cloth Filter Bag
or a Paper Filter Bag.
2 Push the Cloth Filter Bag's rubber seal onto the intake tube. Rest
the bag on top of the bag support platform.
3 Expand the Paper Filter Bag by pulling out the pleats. Hold on to
the cardboard square and push the fi lter bag's rubber seal onto the
intake tube. Rest the bag on top of the bag support platform.
4 Close the Bag Housing. Do not pinch the bag between the cover and
the housing.
OPERATION
1 Plug the Power Cord into a properly grounded outlet. The top cord
hook rotates to quickly release the Power Cord (1).
2 Turn the Main Power Switch (5) ON.
3 Grab the Hand Grips (9) and pull on the Trigger Bar (6) to start the
brush rotation. Release the Trigger Bar (6) to stop brush rotation.
4 Turn the Brush Height Adjustment Knob (3) until the brush just
touches the carpet. If the brush is set too low, the machine will be
hard to push and the motor may be overloaded.
USING THE WAND (BEFORE JUNE 2005)
The machine's built-in Wand makes it easy to clean high surfaces or reach
into tight corners. Simply remove the Wand (4) from its holder and turn
the Control Cable (7a) to the left, pull it out and turn it back to the right to
lock it. After use, turn the Control Cable (7a) to the left, push it back in,
turn back to the right to lock and replace the Wand to its holder.
USING THE WAND (AFTER MAY 2005)
The machine's built-in Wand makes it easy to clean high surfaces or reach
into tight corners. Simply remove the Wand (4) from its holder and turn
the Wand Control Lever (7b) to the right (clock-wise). After use, turn the
Wand Control Lever (7b) to the left (counter clock-wise) and replace the
Wand to its holder.
AFTER USE
1 Unplug the Power Cord and wrap it around the cord hooks.
2 Turn the Brush Height Adjustment Knob (3) to the STORE position.
3 Check the Filter Bag. Empty the Cloth Filter Bag if it is full, inspect
it for damage and replace it if necessary. Replace the Paper Filter
Bag if it is full or damaged.
4 Perform any required maintenance before storage. See the
Maintenance section of this manual for more information.
5 Wipe the machine with a damp cloth.
6 Store the machine indoors in a clean, dry place.
28
™
revised 4/05