Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio housing • B) ISO brackets • C) ISO trim ring
A
Metra. The World's Best Kits.
®
Kia Sorento
KIT FEATURES
• DIN radio provision with pocket
• ISO DIN radio provision with pocket
• Painted matte black to match the factory finish
B
C
MetraOnline.com
2011-2013
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
99-7340B
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . .................................................2
Kit Assembly
– DIN radio provision with pocket........................3
– ISO DIN radio provision with pocket . ................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Please visit metraonline.com
for wiring harness options
Antenna Adapter: 40-KI11
TOOLS REQUIRED
• Phillips screwdriver
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 5/21/18 INST99-7340B
Publicidad
Manuales relacionados para Metra 99-7340B
Resumen de contenidos para Metra 99-7340B
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/21/18 INST99-7340B...
-
Página 2: Dash Disassembly
DASH DISASSEMBLY 1. Remove shifter knob. (Figure A) 2. Remove the shifter surround panel. (Figure B) 3. Remove panel under the heater and air climate controls. (Figure C) 4. Remove (2) Phillips screws from bottom and remove center fascia panel. (Figure D) 5. Remove (4) Phillips screws securing the heater and air climate controls. (Figure E) (Figure A) (Figure B) (Figure C) 6. Remove (4) Phillips screws securing the radio. Slide the radio out, then unplug and remove the radio. (Figure F) Continue to Kit Assembly (Figure D) (Figure E) (Figure F) 1.800.221.0932 MetraOnline.com... -
Página 3: Kit Assembly
3. Snap the pocket into the bottom 3. Snap the pocket into the bottom opening of the radio housing. (Figure B) opening of the radio housing. (Figure B) (Figure A) (Figure A) 4. Slide the radio into the sleeve until it 4. Slide the radio into the top opening clicks in. (Figure B) of the radio housing until it clicks in. (Figure B) 5. Locate the factory wiring harness and antenna connector in the dash. Metra 5. Attach the ISO trim ring to the recommends using the proper mating completed radio assembly. (Figure B) adapters from Metra and/or AXXESS. 6. Locate the factory wiring harness and 6. Secure the radio assembly to the antenna connector in the dash. Metra dash using the factory screws, then recommends using the proper mating reassemble the dash in reverse order of adapters from Metra and/or AXXESS. disassembly to complete the installation. 7. Secure the radio assembly to the dash using the factory screws, then (Figure B) - Página 4 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/21/18 INST99-7340B...
- Página 5 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/21/18 INST99-7340B...
-
Página 6: Desmontaje Del Tablero
DESMONTAJE DEL TABLERO 1. Retire la palanca de cambios. (Figura A) 2. Retire el panel envolvente shifter. (Figura B) 3. Retire el panel debajo del calentador y controles de temperatura del aire. (Figura C) 4. Retire (2) tornillos Phillips de la parte inferior y quitar salpicadero central. (Figura D) 5. Retire (4) tornillos Phillips asegurar el (Figura A) (Figura B) (Figura C) calentador y el control de temperatura del aire. (Figura E) 6. Quite los (4) tornillos que sostienen el radio. Deslice el radio hacia afuera, luego desconecte y retire la radio. (Figura F) Continuará al Ensamble del Kit (Figura D) (Figura E) (Figura F) 1.800.221.0932 MetraOnline.com... -
Página 7: Ensamble Del Kit
3. Coloque a presión el cavidad en la parte inferior de la abertura de la carcasa del inferior de la abertura de la carcasa del radio. (Figura B) (Figura A) (Figura A) radio. (Figura B) 4. Deslice la radio en la abertura superior 4. Deslice el radio en la manga hasta que de la carcasa de radio hasta que haga haga clic. (Figura B) clic. (Figura B) 5. Localice el arnés de cableado de fábrica 5. Coloque el anillo de moldura ISO en el y el conector de la antena en el tablero. ensamble de radio completado. (Figura B) Metra recomienda que use adaptadores 6. Localice el arnés de cableado de fábrica adecuados de acoplamiento de Metra y el conector de la antena en el tablero. y/o de AXXESS. Metra recomienda que use adaptadores 6. Asegure el ensamble de la radio al adecuados de acoplamiento de Metra tablero con los tornillos de fábrica, y/o de AXXESS. luego vuelva a ensamblar el tablero en (Figura B) (Figura B) 7. Asegure el ensamble de la radio al orden inverso al del desmontaje para tablero con los tornillos de fábrica, completar la instalación. - Página 8 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda técnicos con certificación del Programa de Certificación en Electrónica Móvil (Mobile Electronics Certification Program, MECP). Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 5/21/18 INST99-7340B...