Publicidad
Idiomas disponibles
Idiomas disponibles
33. Position components 033063 on landing, using components 002040 and 001004. Drill landing with a 5 mm bit,
keeping a distance between centres that allows at least four balusters to be fitted.
34. Position balusters 127014, with components 031069 facing outwards, and tighten component 001004 (fig. 1).
35. Fix straight handrail 140018 using components 002031 (fig. 1).
36. Depending on position and presence of walls around the stairwell, it may be necessary to position one or two
extra balusters 127014 (fig. 9).
37. In this case, a space must be considered that is at the same distance from the other balusters or from the wall.
Drill landing with a 4.5 mm bit and assemble with components 033063, 001004 and 002040 (fig. 1) (fig. 9).
38. Assembly of floor-mounted balustrade, if applicable. Determine the position of the posts on the floor, on
average one every 28 cm and at a distanza of 8 cm from the edge. Take care: for circular balustrades, use
the circular handrail to determine the distance of the posts from the edge of the floor aperture – this distance
varies according to the radius of the circular handrail supplied. Drill with a Ø 10 mm bit and insert the 046015
components, fixing them with chemical resin (not supplied). Assemble components 033063 with components
009002 and 005001. Insert the 127014 balustrade balusters ( H= 910 mm) into the 033063 components,
with the 126034 reinforcing baluster about every metre, and lock them with components 001004. Fix the
balusters to the wall using component 033010 and items 008004, 011053 and 033056 (drill with an Ø
8 mm bit). Determine the length of the handrails and cut off the excess quantity. Assemble the 140018 or
140073 handrails to the balusters with the 002031 components using items 031076 and 046011 for straight
balustrades and items 031073, 031077 and 002026 for circular balustrades. Assemble any 033103, 033105,
033107 connecting components and the 033103 terminal components (fig. 16).
39. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on each
end baluster of the banisters and also on one intermediate baluster positioned between the two ends of the
banister side. Fasten the cables at one of the two ends using parts 031098 and 001012, leaving about 15mm
protruding from parts 034041; cover with parts 034042 and 001012. Tighten the cables by hand and lock parts
031098 and 001012 respectively working from the lower to the higher end of the steel cable. Once the final
parts 031098 and 001012 have been fastened, cover the ends of the cables with adhesive tape to prevent
them from unravelling whilst being cut. Cut the cables at a distance of 15 mm from parts 034041. Remove the
tape and cover with parts 034042 and 001012 (fig. 1 - 6 - 7).
Final assembly
40. To further reinforce the staircase at intermediate points, fix components 033010 to wall and join to the
balusters, using components 033056. Drill with an 8 mm bit and use components 008004, 011053, 011057,
005035 (fig. 12) (fig. 13).
Assembly of R020 railing
41. Unlock component 005008 and fan out the 103008 steps. It's now possible to ascend the staircase.
42. Fit parts 031067 into holes on treads with edge facing upwards (fig. 2).
43. Starting from the landing, insert the 127002 connecting balusters between the steps, inserting the 033140
component on each step, with the hole in the screw facing in the direction of the ascent. If necessary, cut the
127002 balusters from the lower end to obtain a handrail height of about 100 cm.
44. Position balusters with component 033147 with the part with hole upwards (fig. 2) (fig. 9). Tighten the 001013
components of the steps above and below paying attention to the riser (fig. 2).
45. Carefully check that all balusters positioned are vertical. This is essential for successful final assembly of the
staircase.
46. Definitively tighten component 005008 (fig. 9).
47. Fix component 033144 to floor in position of first baluster, drilling with an 8 mm bit. Use components 011053,
008004, and 001004 (fig. 2).
48. Position the first baluster 127002; adjust height according to the balusters fitted earlier (fig. 2). Insert the
046050 reinforcing component into the 1st baluster.
49. Prepare spiral handrails, components 031073, 002026 and disks 031077; the disks are made in soft
transparent material; take care not to mistake them for parts 031076, made in hard transparent material and to
be used only in the joints of any straight handrails present (fig. 2).
50. Cut the initial handrail by 5 cm and attach the 031061 component, using components 011069 and 004034,
drilling with a Ø 6 mm bit. Start to assemble the handrails onto the balusters with the 002031 components,
starting from the bottom. Continue mounting the handrails, inserting the 031073, 031077 joint components
and the 002026 fixing screws. Make sure the balusters are vertical and rotate the sections of handrail until they
are perfectly aligned (fig. 2).
51. When the last baluster on the staircase is reached, cut excess handrail at right angles with a saw for wood
(fig. 2).
52. Complete handrail by fixing component 031061, using components 011069 and 004034, drill with a 6 mm bit (fig. 2).
10 - GUS
Publicidad
