Publicidad
Idiomas disponibles
Idiomas disponibles
shape of the handrail), the 130202 or 130203 spacer, with the 023041 or 023040 components assembled,
the 131030 or 131031 spacing discs and once again the 103008 step (with the wooden staves parallel to
the specified ascending side ), and so on. Arrange the steps alternately to the right and to the left, so as to
uniformly distribute the weight (fig. 10).
13. When the top of the tube 042013 is reached, screw on component 022003, screw on next tube 042013 and
continue with assembly of staircase (fig. 6).
14. Once the end of 042013 tube is reached, screw the 022001 component to the 046036 component keeping
the threaded hole upwards (screw on the 046036 element, keeping in mind that it must be at the same height
as the landing). Continue to insert the steps using the compensation component 023001 in the 130202 or
130203 spacer, already assembled with 023041 or 023040 washers and 131030 or 131031 spacing discs
(fig. 11).
15. Cut the 023001 component at about 3 mm from the fixed rabbet of the shortest part, inserting it into the
130202 or 130203 spacer, and insert in order the 130202 or 130203 spacer and the 088003 landing. Align
the landing with the small hole (which allows the passage of the baluster) on the leading side of the steps (fig. 9)
16. Insert the 023035, 023037 or 022065, 009010 components and lock the 005008 component (fig. 1) (fig. 2).
Fixing landing
17. Move component 047009 towards ceiling. Determine the position, keeping a distance of about 15 cm from the
outer edge of the landing, drill with a 14 mm bit and definitively secure, using components 008001 (fig. 1) (fig. 2).
18. Fix components 047009 to landing, using components 011053 (drill landing with a 4.5 mm bit).
19. Position components 132016 (fig. 1) (fig. 2).
Assembly of R010 railing (go to point 41 for model R020)
20. Unlock the 005008 component and fan out the 103008 steps. It's now possible to ascend the staircase.
21. Starting from the floor, insert balusters 127010 connecting the treads. If necessary cut the 127010 balusters
from the lower part to obtain a handrail height of about 100 cm. Position the balusters with the 033190
component, with the holed part facing upwards (fig. 1) ( fig. 9). Tighten the 001010 component of the higher and
lower steps according to the riser (fig. 1).
22. Carefully check that all balusters positioned are vertical. This is essential for successful final assembly of the
staircase.
23. Definitively tighten component 005008 (fig. 9).
24. Fix component 033142 to floor in position of first baluster, drilling with an 8 mm bit. Use components 002040,
008004, and 001004 (fig. 1).
25. Position the first baluster 127010; adjust height according to the balusters fitted earlier (fig. 1).
26. Prepare spiral handrails, components 031073, 002026 and disks 031077; the disks are made in soft
transparent material; take care not to mistake them for parts 031076, made in hard transparent material and to
be used only in the joints of any straight handrails present (fig. 1).
27. Cut the initial handrail by 5 cm and attach the 033103 component, using components 011069 and 004034,
drilling with a Ø 6 mm bit. Start to assemble the handrails onto the balusters with the 002031 components,
starting from the bottom. Continue mounting the handrails, inserting the 031073, 031077 joint components
and the 002026 fixing screws. Make sure the balusters are vertical and rotate the sections of handrail until they
are perfectly aligned (fig. 1).
28. Using a wood saw, make a right-angled cut to remove the excess handrail so that it corresponds to the last
baluster on the staircase (fig. 1).
29. Complete handrail by fixing component 033103, using components 011069 and 004034, drill with a 6 mm bit
(fig. 1).
30. Insert the steel cables into the 034041 parts on the banisters, positioning parts 031098 and 001012 on
each end of the banisters and also on one intermediate baluster positioned between the two ends of the
banister side. Fasten the cables at one of the two ends using parts 031098 and 001012, leaving about 15
mm protruding from parts 034041; cover with part 034042 and 001012. Tighten the cables by hand and lock
parts 031098 and 001012 respectively working from the lower to the higher end of the steel cable. Once the
final parts 031098 and 001012 have been fastened, cover the ends of the cables with adhesive tape to prevent
them from unravelling whilst being cut. Cut the cables at a distance of 15 mm from parts 034041. Remove the
tape and cover with parts 034042 and 001012 (fig. 1 - 6 - 7).
31. Complete assembly of railing, fitting components 031064 into the lower part of balusters 127010 and
components 031075 into side of treads (fig. 1).
Assembly of R010 balustrade
32. Screw part 033063 onto stay 046036 with screw 011038 (fig. 1).
9 - GUS
Publicidad
