Clearing The Memory; Memory Full; External Antenna - FAAC XR4 433 C Manual Del Usuario

rised, press buttons P1 + P2 simultaneously, then
release them, the LED flashes.
2. Within 8 seconds, press and hold the button that
has already been memorised, the LED lights up
with a steady light.
3. Bring the radio control that has already been
memorised, into contact face to face with the new
one to be memorised.
4. Press the button to be memorised on the new radio
control and make sure that its LED flashes twice
before turning off.
5. Release all buttons.
6. Press the button on the new radio control that has
just been memorised twice in succession. The associ-
ated output on the receiver activates.
■ MEMORISING RC RADIO CONTROLS
1. Press the button of the receiver that corresponds to
the channel that you wish to associate with the radio
control until the relative LED starts to flash slowly
(DL1->channel 1, DL2->channel 2, DL3->channel
3, DL4->channel 4). When the button is released,
the LED continues to flash for 20 seconds, during
which the codes can be memorised by pressing the
relative buttons of the radio controls.
2. Whenever a code is memorised, the LED of the
receiver lights up steadily for 2 seconds and then
flashes for 20 seconds.
3. If no code is memorised while the LED is flashing,
after 20 seconds the LED switches off to indicate
that the procedure has ended.
4. To memorise additional radio controls at a later
stage, repeat the procedure from step 1.
■ MEMORISING RC RADIO CONTROLS REMOTELY
1. Press buttons P1 + P2 for at least 5 seconds on a
radio control that has already been memorised and
then release them.
2. Within 5 seconds, press and release the button of
the radio control that has already been memorised
to activate the learning phase on the same channel
on the receiver.
3. Press the button on the new radio control within
5 seconds. In the case of multiple radio controls,
repeat this step for each one within 5 seconds of
each other.
■ MEMORISING DS RADIO CONTROLS
1. Set the required combination of the DIP switches
on the radio control (avoid setting them to all On
or all Off).
2. Press the button of the receiver that corresponds to
the channel that you wish to associate with the radio
XR4
control until the relative LED starts to flash slowly
(DL1->channel 1, DL2->channel 2, DL3->channel
3, DL4->channel 4). When the button is released,
the LED continues to flash for 20 seconds, during
which the following step should be carried out.
3. Press and release the button of the radio control that
you wish to memorise. Make sure that the flashing
LED of the receiver becomes steady for 2 seconds and
then flashes again for 20 seconds, during which it is
possible to memorise another radio control with a
different DIP switch combination.
4. Whenever a code is memorised, the LED of the
receiver lights up steadily for 2 seconds and then
flashes for 20 seconds.
5. If no code is memorised while the LED is flashing,
after 20 seconds the LED switches off to indicate
that the procedure has ended.
6. To memorize other radio controls, it is possible
to set a DIP switch combination that has already
been memorised or repeat the procedure for new
combinations.

4. CLEARING THE MEMORY

To delete all the radio codes for channels 1 and 2: press
and hold button SW1 or SW2 until both LEDS DL1 and
DL2 turn on steadily (after approximately 10 seconds).
To delete all the radio codes for channels 3 and 4: press
and hold button SW3 or SW4 until both LEDS DL3 and
DL4 turn on steadily (after approximately 10 seconds).

5. MEMORY FULL

If in step 1 of the memorisation procedure, the LED turns
off instead of continuing to flash for 20 seconds when the
button is released, it means that the memory is full and
it is not possible to memorise any more codes.

6. EXTERNAL ANTENNA

To connect the external antenna (accessory) to terminal
board J3 with the receiver powered off:
1. Remove the antenna wire supplied.
2. Connect the coaxial cable as shown in the figure.
04 532358 - Rev.A