AmerTac Westek LPL704 Manual Del Propietário

LPL704/LPL704W (4 Light Heads) Owner's Manual
Location of Controls
1. ON/OFF Switch/Remote Control Signal Receiver
2. Swiveling Light Heads
3. Battery Compartment*
*On back of unit
Installation
Note: Hook and loop tape may be cut to desired size for easier removal. Remove the mounting bracket if you are
using the hook and loop tape. To do so, hold the light with mounting bracket facing up and the power button facing
you. Slide the mounting bracket to the left and pull up to remove it.
1. Check the location of where you want to place the Track Light. Make sure it is clean and there is no debris or
dust.
2. Two sets of hook and loop tape are included. Place the two pieces of hook and loop tape
together so the hook and loop sides adhere to each other. Repeat this step for the second
set of hook and loop tape.
3. Remove the plastic covering on one sticky side of the tape. Repeat this step for the second
set of hook and loop tape.
4. Place one set of the hook and loop tape in the left and right rectangular recessed areas on
the base of the Track Light.
5. Remove the plastic covering on the other sticky side of the tape. Repeat this step for the
second set of hook and loop tape.
6. Place the Track Light in the desired location. Press fi rmly for fi ve (5) seconds so the tape
adheres to the surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may
remove paint or damage surface.
Screws and Detachable Bracket (included)
1. Remove both pieces of hook and loop tape by pulling the tape away from the base of the
light.
2. Remove the mounting bracket so that it can be used as a template for the screw holes.
To do so, hold the light with mounting bracket facing up and the power button
facing you. Slide the mounting bracket to the left and pull up to remove it.
3. Drill two (2) pilot holes in the location where you want to mount the under cabinet light. Use the detachable
bracket as a guide for the pilot holes.
4. Place screws (included) in pre-drilled holes. Do not over tighten.
5. Clip the under cabinet light to the detachable bracket by aligning and inserting the posts on the bracket into the
keyhole slot openings on the backside of the under cabinet light. Slide the light to the left to lock it into position.
6. To remove the under cabinet light from the detachable bracket, simply slide the light to the right and pull down.
Mounting the Remote Control Hook and Loop Tape (included):
1. Check the location of where you want to place the Remote. Make sure it is clean and free of debris and dust.
NOTE: Polishing or cleaning chemicals on surface may reduce the strength of the adhesive.
2. Remove the paper covering on one side of the hook and loop tape.
3. Place the hook and loop tape in the recessed area in the center on the back of the Mounting Bracket, sticky
side down.
4. Remove the paper covering from the other side of the hook and loop tape. This is the side you will mount to
your desired surface.
5. Place the Mounting Bracket in the desired location. Press fi rmly and evenly for fi ve (5) seconds so that the
hook and loop tape adheres to the surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint, plaster
or damage surface when removed.
Screws (included):
You can secure the EZ-Mount Bracket to almost any surface using 2 screws.
To do so, remove the Remote from the Bracket by sliding it up and out of the Bracket.
Use the printed paper mounting template for pilot hole positions.
1. Drill two (2) pilot holes in the location where you want to mount the Remote Control making sure you are within
15 feet (5 meters) of the LED light.
2. Place screws (included) in pre-drilled holes. Tighten slightly until secure, but do not tighten all the way.
Slide the EZ-Mount Bracket keyhole slots over screw heads and into position.
3. Tighten screws to secure the Bracket to the wall. Take care to not over tighten.
4. Place the Remote Control in the mounting bracket.
Operating Directions
Light Positioning
Each of the four light heads may be positioned independently. They can be rotated 330° left or right as well as
pivoted up and down for the desired light positions.
NOTE: Each light head can only be turned 330° left or right (Fig 1). To prevent damage to the unit, do NOT
overturn the light heads. Doing so may damage the unit and will void the warranty.
ON/OFF Operation
1. Press once to turn light ON.
2. Press again to turn the light OFF.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited express
warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The Limited Warranty
is in lieu of all other express or implied warranties or liabilities subject to the exceptions explained fully in the Limited
Warranty on the website.
LED UNDER CABINET LIGHT
1
Fig 1
Battery Compartment
Housing
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
1. Remove the mounting bracket at the back side of the Under Cabinet Light. To do so,
hold the light with mounting bracket facing up and the power button facing you. Slide
the mounting bracket to the left and pull up to remove it.
2. Slide the battery compartment covers in towards the center of the unit to open the
battery compartments.
3. Remove old batteries, if replacing batteries. Insert six new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended
use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the
battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium)
batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended
period of time.
3
2
ON/OFF/Dimmer Switch
Battery Compartment
Housing
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0092-A