AmerTac Westek LPL622RC Serie Manual Del Propietário

LPL622RC/LPL622WRC/LPL623R /LPL623WRC
Series Owner's Manual
Location of Controls
1. ON/OFF Switch. Selectable dimmer operation. Press to turn on the
light and then hold the button for desired brightness
2. Battery Compartment*
3. Remote Control Signal Receiver (hole on side)
*On back of unit
Remote Control Buttons
3. Power on/power off
4. Adjust brightness + / -
5. Auto-off timer for 15, 30, 60 or 120 minutes
Installation
Hook and Loop Tape (included)
1. Check the location of where you want to place the puck light. Make sure it is clean and that there is no debris or dust.
2. Place the two pieces of hook and loop tape together so that the hook and loop sides adhere to each other. There is a recessed area showing the
optimal position for the hook and loop tape.
NOTE: Hook and loop tape may be cut to desired size for easier removal.
3. Remove the plastic covering on one sticky side of the tape.
4. Place the tape in the center of puck light base. This is the battery compartment side.
5. Remove the plastic covering on the other sticky side of the tape.
6. Place the puck light in the desired location. Press fi rmly and hold for fi ve (5) seconds so that the tape adheres to the surface.
CAUTION: Be cautious of what surface the hook and loop adhesive is attached to, as it may remove paint or damage surface.
Screw (included)
1. Drill a pilot hole in the location where you want to mount the puck light. The hole should be where you want the center of the puck light to be located.
2. Put screw (included) in pre-drilled hole. Do not insert the screw all the way. Leave ½" of the screw out of the hole.
3. Slide battery cover over screw. Prongs should face down as shown.
4. Slide battery cover to the left or the right so that the neck of screw is in the narrow part of the hole. Tighten screw until battery cover is secure to
surface. Do not over tighten. Attach puck light body to battery cover.
Operating Directions
Light positioning
• The LED Puck Light's base can be twisted 360°.
• Pivot the lens up to 30º to light desired area.
YOU CAN OPERATE AND CONTROL THE LIGHT TWO WAYS:
ON/OFF Operation
1. Press once to turn light ON.
2. Press again to turn the light OFF.
Remote Operation Using the Wireless Remote Control
The remote uses Infra Red technology. This is the same type of technology used in most TV remote controls. As such, pointing it at the puck light may be
necessary. For best performance, point remote to the receiver (red lens) of light within 15 feet (5 meters) & 30 degrees directly (unblocked).
1. Press the switch once to turn the LED lights ON.
2. Press again to turn the light OFF.
NOTE: It is recommended to mount the Puck Light with the Remote Control Signal Receiver facing toward where it can receive the remote control
signal.
Changing the Remote Control Batteries
If the Remote Control does not work to turn the LED lights ON, this may be an indication that the battery needs to be replaced.
Replacing the batteries in the remote control –
This product contains a button battery. If swallowed, it could cause severe injury or death in just 2 hours.
Seek medical attention immediately.
REMOTE CONTROL - CR2025 battery required.
1. Loosed battery compartment retaining screw.
2. Slide battery drawer out.
3. Remove battery.
4. Place new battery in position aligning polarity (+) (-) as indicated.
5. Slide battery drawer in.
6. Tighten battery compartment retaining screw.
This product contains a Button battery. If swallowed, it could cause severe injury or death in just 2 hours.
Seek medical attention immediately.
Inserting/Replacing the Batteries
If the LEDs appear to be dim this is an indication that your batteries need to be replaced.
To Install Batteries for the First Time:
Remove battery compartment housing at the back of the puck light. To do so, hold the front of the puck light in one hand, with the other hand grab fi nger
grips on battery compartment cover and pull away from puck light. The cover will pop off.
NOTE: It may help to turn the light head or battery compartment cover clockwise or counter-clockwise as you are pulling it off.
To Replace Batteries Once Puck Light is Mounted:
1. Puck Light body will release from battery compartment cover/mounting bracket easily. Place fi ngers around Puck Light body and pull down gently to
release light head and expose battery compartment.
2. Remove old batteries (if replacing batteries).
3. Replace with three (3) new AAA batteries.
4. Make sure to follow battery polarity guide when installing new batteries.
5. Replace battery compartment housing.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to
the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited
express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The
Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions
explained fully in the Limited Warranty on the website.
REMOTE CONTROLLED
WIRELESS LED PUCK LIGHTS
2
1
5
3 3
Puck Light Body
Finger Grips
(for Removing
Battery Compartment)
Battery
Compartment
Cover
BATTERY
COMPARTMENT
COVER
Main Unit
Retaining
Screw
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0066-A
4
6