AmerTac Westek LPL641MW Manual Del Propietário

LPL641MW Owner's Manual
Location of Controls
1. ON/OFF/DIMMER Switch
2. Motion Sensor
3. Light Head Swivel Knob
4. Battery Compartment*
5. Motion Sensor Activation Switch
*Underneath unit
Screws and Detachable Bracket (included)
1. Remove the mounting bracket so that it can be used as a template for the screw holes.
To do so, hold the light with mounting bracket facing up and the LEDs facing you.
Slide the mounting bracket to the left and pull up to remove it.
2. Drill two (2) pilot holes in the location where you want to mount the under cabinet light. Use the detachable
bracket as a guide for the pilot holes.
3. Place screws (included) in pre-drilled holes. Do not over tighten.
4. Clip the under cabinet light to the detachable bracket by aligning and inserting the posts on the bracket into the
keyhole slot openings on the backside of the under cabinet light. Slide the light to the left to lock it into position.
5. To remove the under cabinet light from the detachable bracket, simply slide the light to the right and pull down.
Operating Directions
Light Positioning
Light head rotates by using the Light Head Swivel Knob. Simply turn the knob
to direct light where you need it.
NOTE: To prevent damage to the unit, do NOT overturn the light head.
Doing so may damage the unit and will void the warranty.
ON/OFF/DIMMER Operation
1. Press once for full brightness.
2. Press again for softer light.
3. Press a third time to turn the light off.
Motion Sensor
The light features an optional Motion Sensor which when activated will turn the light ON automatically when motion is
detected. The light will also shut OFF automatically, after a period of time when no motion is detected. It detects motion
within 6.6 feet (2m) of the motion sensor. To use this feature, simply slide the motion sensor activation switch to the
desired location.
NORMAL - Motion sensor is inactive. (Use main ON/OFF Switch to activate the light.)
AUTO-30S - LEDs will turn OFF after 30 seconds if no motion is detected.
AUTO-60S - LEDs will turn OFF after 60 seconds if no motion is detected.
Perfect for use inside cabinets and closets.
Motion sensor is designed to detect motion within 6.6 feet (2m) of sensor. For best operation wave hand at a medium
speed in front of motion sensor to activate light.
Inserting/Replacing the Batteries
This light operates with 3 or 6 batteries. If the LEDs appear to be dim this is an indication that your batteries need to
be replaced.
1. Remove battery compartment from accent light.
2. Remove old batteries (if replacing batteries).
3. Replace with three (3) new AA batteries for 20 hour run time or six (6) new AA batteries for 40 hour run time.
4. Make sure to follow battery polarity guide when installing
new batteries.
5. Replace battery compartment housing.
Battery Precautions:
1. Use only the size and type of batteries specifi ed.
2. Always purchase the correct size and grade of battery most suitable for the intended use.
3. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
4. Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel Cadmium) batteries.
5. Replace all batteries of a set at the same time. Do not mix old and new batteries.
6. Clean the battery contacts and also those of the device prior to battery installation.
7. Do not dispose of batteries in fi re.
8. Remove batteries if consumed or if product is to be left unused for an extended period of time.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Modifi cations to this product not approved by the party responsible for compliance could void the user's authority to operate the product.
Limited Warranty
Under normal use and conditions, AmerTac provides to the original purchaser of this product a one year limited
express warranty that is set forth in the Limited Warranty stated in full at www.amertac.com/warranties. The
Limited Warranty is in lieu of all other express or implied warranties or liabilities subject to the exceptions
explained fully in the Limited Warranty on the website.
WIRELESS LED LIGHT BAR
1
2
3
4
MOTION ACTIVATED
5
AA Run Time
3 20 hours
6 40 hours
If using 3 batteries,
place in postion
shown in gray
250 Boulder Dr.
Breinigsville, PA 18031
610-336-1330
www.amertac.com
Made in China / Fabriqué en
Chine / Fabricado en China
© 2018 AmerTac™
I18-0074-A