Brigade Electronics BE-650 Manual De Instrucciones página 6

ENGLISH
BE-650 BACKEYE REARVIEW CCTV SYSTEM
INTRODUCTION
This BACKEYE system has been designed to provide years of trouble-
free operation. Please read this manual thoroughly. This manual con-
tains instructions to make the installation of the camera and monitor
easier. This BACKEYE system is a supplement to standard rear-view
mirror systems, and will provide additional rear-view vision when
installed and maintained properly.
It is not intended in any way to be a substitute for careful and cautious
driving. All applicable traffic laws and motor safety regulations must still
be adhered to
FEATURES
BE-650C CAMERA
• 270,000 pixel image sensor
• 3 Lux sensitivity
• Automatic electronic iris provides a clearer, more consistent image
in low and bright light
• Compact design and lightweight ease installation in most vehicles,
including large boats
• Durable, waterproof construction
• Built-in microphone for audio pick up (See Fig. 6)
• Waterproof cable connection
• Wind deflector reduces build up of dirt on lens
BE-650M TFT LCD COLOUR 5.0" MONITOR
• Day/night switch
• Brightness control
• Colour control
• Volume control
• Two camera inputs and Camera Selector Switch
• Power/stand-by switch
• Mirror/Normal selection switch
• Illuminated front panel
• Monitor pigtail:
• Power socket
• Camera 1 and Camera 2 input socket
CONTENTS OF 1 COMPLETE SYSTEM
BE-650C CCD CAMERA
1-Camera
1-Camera bracket
4-Attachment screws with washers (M4 x 8)
1-Wind deflector
BE-650M MONITOR
1-Monitor
1-Snap-on sun visor
1-Monitor bracket
1- Power harness with locking connector
BEFORE INSTALLATION
1. This system operates from 10 volts DC to 32 volts DC, negative
ground.
2. Please install this system according to the instructions in this manu-
al.
3. Do not disassemble the camera or the monitor. This voids the war-
ranty. Disassembling the camera will compromise the
waterproof seal.
4. Connect the system to an ignition switched power source.
Connection to a battery source will reduce battery life.
WARNING
1. To prevent electrical shock, DO NOT OPEN THE MONITOR CASE.
There are potentially lethal voltages inside the monitor. There are no
user serviceable parts inside. If evidence of tampering is detected,
the warranty will be considered void
2. Keep monitor away from leaking water, rain, moisture etc. It is NOT
waterproof. Any moisture inside the monitor could cause extensive
damage
3. Use the thumbscrews to mount the monitor to bracket.
4. Do not cover air ducts. Monitor needs proper ventilation to prevent
overheating
INSTALLATION INSTRUCTIONS
BE-650C CAMERA
1. Attach camera bracket (see Fig. 1) to upper portion of vehicle.
Attachment point must be sturdy enough to support camera and
bracket.
2. Attach camera to bracket using M4 bolts provided. Adjust angle as
indicated in Fig. 2. (Use rear bumper and back of vehicle as a refer-
ence point.)
3. Wind deflector may be installed. The deflector is designed to reduce
the build up of dust, dirt and moisture on the camera lens. (See
Fig.3.)
All manuals and user guides at all-guides.com
BE-650M MONITOR
1. Attach monitor inside vehicle in a location convenient to the driver
(e.g. centre of dash, overhead or in dash). (See Fig.3.)
2. Use a compression plate to attach the monitor bracket to the dash
or overhead. (See Fig. 3.)
3. Adjust mounting angle of the monitor to allow driver to easily view
the screen from all seat positions. (See Fig. 4.)
4. If necessary, snap sun visor into groove on front face of monitor,
Press all (4) sides of the visor to snap it into place.
CABLE
1. The camera to cable connection and the monitor pigtail are water-
proof. Be sure to orient the cables properly.
2. Do not run the cable over sharp edges or corners. Do not kink the
cable. Keep the cable away from hot and rotating parts.
3. Place all excess cable in convoluted tubing.
4. Wire the cable securely.
WIRING CAMERA AND MONITOR
1. See wiring diagram for connections to ignition, ground and back up
circuit. (See Fig. 5.)
2. Wiring camera: Drill a 22mm diameter hole into vehicle body near
the camera and bracket. Connect camera connector to extension
cable in vehicle. Push extra cable into vehicle (be careful not to kink
cable) and fit grommet into hole. Apply sealant around grommet to
increase resistance to water penetration.
3. Wiring monitor pigtail: Insert extension cable into camera 1 and
camera 2 position. Bundle excess cable together using a cable tie
or vinyl tape. This will avoid possible damage to cable during opera-
tion. (Fig. 5)
4. Wiring power cable: The red wire is connected to an ignition power
source, the black wire is connected to chassis ground, and the
green wire is connected to the vehicles back up circuit.
FUNCTIONS AND OPERATION
MONITOR
1. CAMERA BUTTON
Depress the camera button to select the camera connected to the
camera 1. Press the camera button to select the camera connected
to the camera 2.
2. NIGHT/DAY SWITCH
When viewing pictures at night or in a tunnel change the picture
brightness by pressing the night/day switch.
3. CAMERA/AV BUTTON
Depress the button to select the camera (CA1, CA2) and press the
button to select the AV inputs signal (AV1, AV2).
4. ON/STANDBY
Press the power switch to turn the monitor on and off
When reverse gear is selected the images picked up by camera 1
will be shown on the monitor.
5. SNAP ON SUN VISOR
6. SPEAKER
7. VOLUME CONTROL
Adjust the volume control for the desired sound level.
8. BRIGHT CONTROL
Adjust the Bright control for the best overall picture.
9. COLOUR CONTROL
Adjust the Colour control for the best overall picture.
10. AUDIO/VIDEO INPUT JACK 1 and 2
For just monitoring on screen, put the plug of A/V signal into this
Jack.
11. AUDIO/VIDEO OUTPUT JACK
Connect audio, video output connector to a second monitor or VCR
input with a RCA phone type connector cable.
12. MIRROR/NORMAL SELECTION SWITCH 1 and 2
When the switch is in MIR position, the picture will show reverse
image.
When the switch is in NOR position, the picture will show a normal
image. *Camera 1 & Camera 2 are operated individually.
CAUTION
1. DO NOT OPEN THE CAMERA CASE. This will break the camera's
waterproof seal. If evidence of tampering is detected, the warranty
will be considered void.
2. We do not recommend mounting the camera near the lower area of
the vehicle (e.g. bumper). This reduces the view of the camera and
increases the chance of physical damage to the camera.
3. Use only the Inner Hexagonal screw and washers to mount the
camera.
MAINTENANCE
Remove dust and dirt with a damp soft cloth. Heavier dirt should be
removed with a damp soft cloth and mild detergent. Do not use strong
cleaning agents containing gasoline, thinner, benzene or alcohol. These
substances may damage the exterior surface of the monitor.
CAUTION
1. Before drilling, be sure no cable or wiring is on the other side. Be
sure to drill a 22mmdiameter hole only.
2. Feed as much cable as possible into vehicle and clamp securely.
This reduces the possibility of it being hooked or snagged.
3. Keep all cables away from HOT, ROTATING and ELECTRICALLY
NOISY components.
4. To increase protection of cable, place all excess wire and extension
cable in convoluted tubing.
5. Do not twist camera cable and do not cut camera pigtail or cable.
SPECIFICATIONS
BE-650C CAMERA
VIDEO SYSTEM NTSC/PAL
PICK-UP DEVICE CCD
IMAGE SIZE 1/3 inch
SYNCHRONIZATION INTERNAL
REQUIRED ILLUMINATION 0.1 lux MINIMUM
VIDEO OUTPUT 1V (p-p), 75 ohm
OPERATING VOLTAGE 12Vdc
POWER CONSUMPTION MAX 2.4W (AT 12V dc)
OPERATION TEMPERATURE -20∞C TO +50∞C
WEIGHT 0.48Kg
DIMENSION (W x H x D) mm 62 x 38 x 57
BE-650M MONITOR
VIDEO SYSTEM NTSC/PAL
PICTURE TUBE 6.4 inch COLOUR TFT LCD SCREEN
PICTURE RESOLUTION 960(H) x 234(V)
AUDIO OUTPUT 0.5W (8 ohm)
POWER CONSUMPTION MAX 5.4 Watts
OPERATION TEMPERATURE -10°C TO + 60°C
OPERATION VOLTAGE DC10 V TO DC32 V
WEIGHT APPROX. 460g
DIMENSION (W x H x D) mm 181 x 136 x 32
DISCLAIMER
The use of the BE-650 BACKEYE Observation system should not in any
way be used as a substitute for careful and cautious driving. Traffic
laws and motor safety regulations must always be adhered to.