Operating Instructions; Important - DieHard 28.71326 Manual Del Usuario

BATTERY TYPE BUTTON
This selects the type of battery to charge.
• Standard – Used in cars, trucks and
motorcycles, these batteries have vent caps
and are often marked "low maintenance" or
"maintenance-free". This type of battery is
designed to deliver quick bursts of energy
(such as starting engines) and has a greater
plate count. The plates are thinner and have
somewhat different material composition.
Regular batteries should not be used for
deep-cycle applications.
• AGM – The Absorbed Glass Mat
construction allows the electrolyte to be
suspended in close proximity with the
plate's active material. In theory, this
enhances both the discharge and recharge
WARNING: A spark near battery may cause
a battery explosion.
IMPORTANT: Do not start the vehicle with
the charger connected to the AC outlet, or it
could result in damage to the charger
CHARGING A BATTERY IN THE VEHICLE
1. Turn off all the vehicle's accessories.
2. Keep the hood open.
3. Clean the battery terminals.
4. Place the charger on a dry, non-
flammable surface.
5. Lay the AC/DC cables away from any
fan blades, belts, pulleys and other
moving parts.
6. For a negative-ground vehicle (as in
most vehicles), connect the charger's
POSITIVE (RED) clamp to the POSITIVE
(POS, P, +) battery post. Next, connect
the charger's NEGATIVE (BLACK) clamp
to the vehicle chassis or engine block,
away from the battery.
7. For a positive-ground vehicle, connect the
charger's NEGATIVE (BLACK) clamp to the
NEGATIVE (NEG, N, -) battery post. Next,
connect the charger's POSITIVE (RED)
clamp to the vehicle chassis or engine
block away from the battery. NEVER
connect any clamps to the carburetor, fuel
lines or sheet-metal body parts.
8. Connect the charger to an electrical outlet.
9. Select the battery type and charge rate.
10. When charging is complete, disconnect
the charger from the AC power, remove
the clamps from the vehicle's chassis,
and then remove the clamp from the
battery terminal.
All manuals and user guides at all-guides.com
• Gel – The electrolyte in a GEL cell has a

OPERATING INSTRUCTIONS

• 6 •
efficiency. The AGM batteries are a variant
of Sealed VRLA (valve regulated lead-acid)
batteries. Popular uses include high-
performance engine starting, power sports,
deep-cycle, solar and storage batteries.
silica additive that causes it to set up or
stiffen. The recharge voltages on this type of
cell are lower than those for other styles of
lead-acid battery. This is probably the most
sensitive cell in terms of adverse reactions to
overvoltage charging. Gel batteries are best
used in VERY DEEP cycle application and
may last a bit longer in hot weather
applications. If the wrong battery charger is
used on a gel cell battery, poor performance
and premature failure will result.
CHARGING A BATTERY OUTSIDE
OF THE VEHICLE
1. Place battery in a well-ventilated area.
2. Clean the battery terminals.
3. Connect a 24-inch long, 6-gauge (AWG)
insulated battery cable to the NEGATIVE
(NEG, N, -) battery post (i.e., jumper
cable) (not provided).
4. Connect the POSITIVE (RED) clamp to
the POSITIVE (POS, P, +) battery post.
5. Position yourself and the "negative post
extension" cable as far away from the
battery as possible, and connect the
NEGATIVE (BLACK) clamp to the cable's
free end.
6. Connect the charger to the electrical outlet.
7. Select the battery type and charge rate.
8. When charging is complete, disconnect
the charger from the AC power,
disconnect the negative clamp, and finally
the positive clamp.
9. A marine (boat) battery must be removed
and charged on shore.
NOTE: This charger is equipped with an
auto-start feature. Current will not be
supplied to the battery clamps until a battery
is properly connected. The clamps will not
spark if touched together.
AUTOMATIC CHARGING MODE
When an Automatic Charge is performed,
the charger switches to the maintain mode
automatically after the battery is charged.