Troubleshooting Guide; Need Help - Good Earth Lighting SE1249-WH3-02LF7-G Manual Del Usuario

1
ON
OFF
MANUAL OVERRIDE allows the light to turn on at any time, by overriding
all sensor controls. It will go back to motion activations the next night.
2
Before doing any work on the fixture, shut off power supply at the circuit breaker panel to avoid electrical shock.
PROBLEM
Security light 1. Light switch is off.
does not come on.
2. Fuse is blown/circuit breaker has tripped.
3. Fixture not properly wired to junction box.
4. Light is detected by sensor.
5. Motion sensor is pointed in the wrong direction.
6. Air temperature is about the same as a person's body
temperature and the (PIR) sensor cannot "see" the person.
Light continuously 1. Light sensor is triggered by reflected light from the security light itself.
cycles ON and OFF
2. Heat is being reflected from other sources and may be triggering
(Strobe effect).
sensor on and off.
Light turns on during 1. Light may be installed in shadows/dark area.
daylight hours.
2. The MINUTES control knob is set to MOTION TEST.
1. Sensor may be triggered by an animal or passing car.
Light comes on for
No apparent reason.
2. Hot air (dryer vent, car exhaust, etc.) may trigger the sensor.
1. Motion sensor may be picking up a continuous flow of warm air from
Light stays on
an air vent, dryer vent or heat reflecting off a surface.
Continuously.
2. Interference generated from transformers, fluorescent light fixtures or
electric motors are connected to the same circuit.
1. The MINUTES control knob is set to MOTION TEST.
Light flashes on for
20 Seconds at a time
day or night.
Light head slips 1. Star knobs are loose.
down.
Light output is to 1. Brightness button was pressed to many times.
bright or to low.
Light output is too 1. Press white light selection button to desired light temp.
warm,neutral,cool.
REPLACEMENT PARTS LIST: Hardware Kit: ZH-SE1249-F01-WH3
Good Earth Lighting - 10 YEAR LIMITED WARRANTY: The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (10) years
®
from the date of original purchase by the consumer. The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment.
We will repair or replace (at our option) the unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge.
Defective units must be properly packed and returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838
to obtain a return authorization number and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any
case limited to replacement of the defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This
limitation upon the liability of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature;
(III) based upon theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty
gives you specific rights, and you may also have other rights which vary from state to state.
FCC STATEMENT: This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has
been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into an outlet on a circuit different from that of the receiver. 4) Consult the dealer or
an experienced radio/TV technician for help.

Need Help?

Good Earth Lighting 1400 East Business Center Drive, Ste. 108 Mount Prospect, IL 60056
®
Good Earth Lighting is a registered trademark of Good Earth Lighting, Inc. © 2020 Good Earth Lighting, Inc.
®
TWO WAYS TO OVERRIDE MOTION SENSOR:
ON ON
OFF OFF
2 Seconds
SWITCH CONTROL MODE
Switch Control allows the light to turn on at any time, by overriding all sensor controls, so the light comes on
regardless of time of day.
NOTE: If the fixture is in Switch Control Mode the built-in light Sensor functions will not work. If you want to
temporarily override the dusk to dawn and motion sensor functions, then you should use the manual override
directions (see Above).
SET MINUTES KNOB TO
Switch Control

TROUBLESHOOTING GUIDE

POSSIBLE CAUSE
Please visit our website at: www.goodearthlighting.com/support or call the Customer Care Center
1-800-291-8838, 8:30 a.m.-5 p.m., CST, Monday-Friday.
SETTING THE LIGHT MANUAL OVERRIDE
If the security light has been turned off at the switch, turn it on for 60 seconds to allow
ON
the (PIR) sensor time to warm up prior to initiating the manual override sequence.
To switch over to manual mode, switch the power OFF-ON-OFF-ON within 2 seconds.
There are 2 ways to return to sensor control:
OFF
1) To immediately switch out of manual mode, repeat the manual mode sequence of
power OFF-ON-OFF-ON within 2 seconds. This will cancel out manual mode.
2) The security light will remain on until the built-in sensor detects the next dusk-dawn
cycle. Once light is detected, it will allow the motion sensor to return to controlling
the fixture the next day.
SET DISTANCE KNOB TO
Any distance.
1. Turn light switch on.
2. Replace fuse/ turn the circuit breaker back on.
3. Discontinue use, call an electrician.
4. Recheck at night.
5. Readjust motion sensor.
6. Decrease the DISTANCE control setting.
1. Change the position of the light head, aim light away from the reflecting surfaces.
2. Decrease the DISTANCE control setting.
1. Light is operating as it was designed. Use manual override if necessary. Or
set to "switch control".
2. Set the MINUTES control knob somewhere between 1 and 10.
1. Decrease the DISTANCE control setting as necessary.
2. Increase the DISTANCE control setting as necessary.
1. Reposition the motion sensor.
2. Install the light on a circuit without transformers, fluorescent light
fixtures or electric motors connected to the circuit.
1. Set the MINUTES control knob somewhere between 1 and 10.
1. Reposition light head and tighten star knobs.
1. Press the low/high beam control button once to change the high/low beam.
1. Press white light selection button to change to a warmer, more neutral or
cooler white light selection.
OR
SET WALL SWITCH TO
ON
CORRECTIVE ACTION
Printed in Vietnam
4