Publicidad
Enlaces rápidos
CFR2115, CFR2127, CFR2136, CFR2144
Instruction Manual
We are here to help!
Please contact Customer Service with any questions.
Customer Service
Americas: 800-359-5520 • 651-484-7988 • info@sanus.com
Europe, Middle East, and Africa: + 31 40 2324700 • europe.sanus@milestone.com
Asia Pacifi c: 86 755 8996 9226 • sanus.ap@milestone.com
·
·
SANUS
2221 Hwy 36 West
Saint Paul, MN 55113 USA
©2011 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone.
All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners.
sanus.com
(6901-002133 <00>)
Publicidad
Manuales relacionados para Sanus CFR2115
Resumen de contenidos para Sanus CFR2115
- Página 1 Saint Paul, MN 55113 USA ©2011 Milestone AV Technologies, a Duchossois Group Company. All rights reserved. Sanus is a division of Milestone. All other brand names or marks are used for identifi cation purposes and are trademarks of their respective owners.
- Página 2 Suomi - Oppaan käyttäminen English - How to use this manual For best results, reference both the text and illustrations. Saavutat parhaan tuloksen tutustumalla sekä tekstiin että kuviin. This item is optional Leikkaa katkoviivaa pitkin ja yhdistä kuvat ja suomenkielinen teksti. English Text Pages 4-17 Tämä...
- Página 3 6901-002133 <00>...
- Página 4 IMPORTANT SAFETY INSTRUCTIONS – SAVE THESE INSTRUCTIONS – PLEASE READ ENTIRE MANUAL PRIOR TO USE Thank you for choosing a Sanus Component Series Rack. The CFR21 series is designed to support audio/video equipment. The total weight capacity for the CFR21 series: CFR2115 226.8 kg (500 lb)
- Página 5 Supplied Parts and Hardware [02] x 2 [03] x 4 [04] x 4 [05] x 16 [01] x 1 [07] 2 Per Shelf [06] CFR2115 1 Per Shelf CFR2127 12 CFR2115 CFR2136 16 CFR2127 CFR2144 18 CFR2136 CFR2144 6901-002133 <00>...
- Página 6 Install Feet and Casters Install feet [03]. Install Casters [04] using screws [05]. [03] [04] [05] Level Feet Adjust the feet [03] to level the rack. Tighten nuts (N) until they are fl ush with the bottom of the rack. CAUTION: To avoid potential injury or property damage, always ensure that your rack is level.
-
Página 7: Cable Management
Remove Cable Access Panels for Cable Management 6901-002133 <00>... - Página 8 Verify the Grounding Strap has been Installed If the grounding wire has not been installed, install the wire now by attaching one end to the door ground stud, and the other end of the ground wire to the ground stud on the bottom of the rail.
- Página 9 Adjust Shelves and Blanking Panels NOTE: Align the bottom of the shelf or blanking panel (B) with the lines (L) on the rack rail. 6901-002133 <00>...
- Página 10 Adjust Rack Rails Remove the shelves and blanking panels before adjusting the rails. Adjust the top and bottom, and right and left rails evenly. NOTE: For clarity, the front door, top, and side panels are not shown. 6901-002133 <00>...
- Página 11 Load Your Components CAUTION: To prevent tipping, always load the rack from the bottom up, and load the heaviest item in the rack fi rst. 50% of the total weight should be mounted in the lower 1⁄3 of the rack. Rack Shelf Backstops NOTE: rear view with back panels removed.
- Página 12 Switch Back Panels To switch the position of the back panels: Remove large upper panel. Remove small lower panel and frame. Fit bottom of large panel into rack frame and angle the panel up until sliding locks snap in place. Flip small panel 180 degrees.
- Página 13 Reverse the Front Door Remove the door Remove the door grounding wire from bottom of rack and the door. Turn upper door pin to release from locking tab and pull down to release door from rack and lift door from rack frame. Release upper pin and turn it back to secure it under the locking tab.
- Página 14 Reverse the Front Door - continued Flip the door Fit spacer onto bottom pin and fi t bottom pin into bottom mounting hole in rack. Turn upper pin to release from locking tab and pull down. Fit pin into upper mounting hole in rack. Release pin and turn pin to secure it under locking tab Reattach grounding wire.
- Página 15 Reverse the Front Door - continued Flip the door handle Remove screws and bracket. Flip the door handle. Reattach screws and bracket. Loosen the locking cam screw. Flip the locking cam tab to the Tighten the locking cam screw. side nearest the edge of the door.
- Página 16 Add Keyed Lock to Door Install keyed lock (purchased Remove plug from side panel. separately) in plug hole. Manage Cables Use tie bars (TB) to bundle cables and wires. (TB) 6901-002133 <00>...
- Página 17 Ganging Racks Remove side panels on sides to be Move racks together until sides are connected. touching. IMPORTANT Make sure both racks are level with each other. Fit 4 ganging clips (GC) into frame slots. Press down on clips to secure. IMPORTANT Make sure all 4 ganging clips are fully engaged.
- Página 18 Suomi English Milestone AV Technologies and its affi liated corporations and subsidiaries (collectively, “Milestone”), Milestone AV Technologies sisar- ja tytäryhtiöineen (yhdessä Milestone) on pyrkinyt tekemään intend to make this manual accurate and complete. However, Milestone makes no claim that the tästä...