Publicidad
XVC/200+XC/310
1/6
2/7
3/8
4/9
5/10
zioni allegate al supporto da parete XKP/300.
SMALTIMENTO
Assicurarsi che il materiale d'imballaggio non
venga disperso nell'ambiente, ma smaltito
seguendo le norme vigenti nel paese di utilizzo
del prodotto.
Alla fine del ciclo di vita dell'apparecchio evita-
re che lo stesso venga disperso nell'ambiente.
Lo smaltimento dell'apparecchiatura deve esse-
re effettuato rispettando le norme vigenti e privi-
legiando il riciclaggio delle sue parti costituenti.
Sui componenti, per cui è previsto lo smaltimen-
to con riciclaggio, sono riportati il simbolo e la
sigla del materiale.
INSTRUCTIONS FOR USE
GB
AND INSTALLATION
INTERCOM HANDSET MODULE XC/310
Intercom receiver compatible with the X2 TECH-
NOLOGY system and system 300.
Using this unit, intercom installations with up to
10 units can be set up. By means of selector
VSE/300, secrecy of speech during conversa-
tions is assured.
It can store up to 3 numbers for calls from entry
panels. In video entry control installations, it can
control the video module and manage auxiliary
2 and self-connection for entrance monitoring
controls.
The unit can be connected directly to the audio
or video entry control installation and can use
4
intercom call buttons as auxiliary service con-
trols. Calls from the entry panel can be indivi-
dual, for a single group or for all receivers asso-
ciated with the same VSE/300.
It features a CNH connector (fig. 2) for connec-
tion to wall mounting XKP/300.
It features the following controls (fig. 1):
1÷5 Call buttons
Doubling button (for calls 6-10)
•
Auxiliary services/porter call
•
2
Door lock release (
(
1
) This control can only be used if the unit is on.
1
NOTE. The LED lights to advise the user that the
doubling function is enabled, whilst the same
5
LED flashes once the receiver is lifted to report
line busy status where a conversation between
receivers is already in progress.
Call transfer
During a conversation between receivers, an
acoustic warning sounds to advise the occupant
that there is a call from the entry panel.
Pressing one of the call buttons and replacing
the receiver transfers the conversation to a diffe-
rent receiver.
The unit receiving the transferred call can, in
turn, retransfer it to another.
Function of each terminal
Terminal block M1
B line
personal door-bell
– ground
6A
call repeater
Function of jumper SW1
The unit usually comes with the jumper inserted.
Remove the jumper if you want to attenuate call
note volume (fig. 2).
Personal door-bell button
The video handset is fitted with a differentiated
call input (terminal
and external entry panel) a continuous tone call
(approximately 2 s).
Programming
To programme calls in system 300 or X2 TECH-
NOLOGY system installations, see the literature
supplied with the units.
To programme intercom calls, see the instruc-
tions supplied with selector VSE/300.
Technical features
• Power supply: from data line itself.
• Current demand: < 5 mA with LED on.
• Audio/data connection line: non polarized twi-
sted pair Z = 100 Ω.
• Working temperature range: 0 °C to +35 °C.
Installing handset module XC/310
Having removed the casing (front screw in fig. 5,
bottom) and receiver, fasten the housing directly
to the wall (fig. 6A) or to the embedding box (fig.
6B or 6C).
If walls are not perfectly flat, take care not to
overtighten screws. Perform the wiring. Refit its
casing and apply the two sides (fig. 7 and 8).
Insert the receiver's cable connector in the hou-
sing and hang up the receiver (fig. 8).
The handset features a name card on which you
can write relevant data. Remove the glass cover
to insert the name card (fig. 8).
WARNING. For installations with XA/300LR, we
recommend that you make a note of the receiver
ID (SN) identification codes, attached to the out-
side of the casing, and write them in the tables
attached to the XA/300LR, MPP/300LR and
IPC/300LR appliances.
XV/200(XVC/200)+XC/310
INTERCOM VIDEO HANDSET
Internal unit with video and secrecy of speech.
With this apparatus, the video signal may be
transmitted by either a coaxial or a twisted pair.
Can be either wall or table-top versions using
the relevant mounting.
XV/200 MONITOR MODULE
1
)
It is equipped with the following controls (fig. 3):
•
XVC/200 COLOUR MONITOR MODULE
It is equipped with the following controls (fig. 4):
•
(
1
) The activation of the video handset and its
subsequent connection to the external entry
panel, are only possible if the system is not
engaged by other conversations.
(
) This control can normally only be used with
2
) (i.e.: for calls from landing
Entry panel activation/selection (
Centralized control (stair light or other ser-
vices) (
2
)
Contrast
Brightness
Entry panel activation/selection (
Centralized control (stair light or other ser-
vices) (
2
)
Saturation colour
Brightness
1
)
)
1
3
Publicidad
