Phonic DFX 2000 Manual Del Usuario página 11

Dynamic effects
Compressors are signal processors that reduce signals over a
user-defined threshold by a user-defined amount/ratio. Limiters
work just as Compressors do, with an infinity-to-1 ratio. A noise
Gate is a signal processor that turns off or significantly attenu-
ates the audio signal passing through it when the signal level
falls below a user adjustable threshold. An Expander helps to
make troublesome background noise (such as humming) inau-
dible by reducing signals with low amplitudes. A De-noiser also
eliminates noise and interference. A De-esser will help to reduce
sibilance in the human voice.
Parameter What it does
Adjusts the input gain of the
Gain
compressor, limiter, expander
Ratio Adjusts the compressor / expander ratio
Adjusts the threshold of the gate,
Threshold
compressor, expander effect
Adjusts the gate/compressor knee-
Knee
curve from sharp to smooth
Adjusts the time it will take for the effect
Attack time to kick in after the signal rises above
the set threshold
Adjusts the time it will take for the effect
Release time to deactivate after the signal falls below
the set threshold
Compressor Adjusts the threshold of the
threshold compressor/limiter effect
Adjusts the threshold at which the
Limiter threshold
limiter will kick in
Adjusts the time the gate or de-noiser
Hold time
will remain open/active
Adjusts the frequency which will be
BPF
decreased for the de-esser
Q Q factor
Psycho-acoustical effects
Parameter What it does
Adjusts the cut off frequency of the high
HPF
pass filter
Drive Adjusts the strength of the exciter effect
Activates harmonic amplification
Harmonic
dependent on the input level
Gain Allows for gain correction
Guitar Distortion effect
Guitar distortion is used for exactly what the name suggests: dis-
torting guitar signals. You can hear guitar distortion in most of the
most popular rock songs going back decades.
DFX2000
Parameter What it does
Drive Adjusts the distortion level
Level Adjusts the volume
EQ low 1 Adjusts the low EQ
EQ low 2 Adjusts the low EQ
EQ high 1 Adjusts the high EQ
EQ high 2 Adjusts the high EQ
Filter/EQ effects
The Graphic EQ effect allows you to use the 4 Effect controls to
adjust 5 separate Equalization bands (predetermined).
Parameter What it does
Adjusts the rate/speed of low
L.F.O.
frequency oscillations
Adjusts the depth of the signal at 200
Freq1_Depth
Hz
Adjusts the depth of the signal at 500
Freq2_Depth
Hz
Adjusts the depth of the signal at 1.12
Freq3_Depth
kHz
Adjusts the depth of the signal at 2.8
Freq4_Depth
kHz
Adjusts the depth of the signal at 8
Freq5_Depth
kHz
Adjusts the phasing of the signal at
Phase 1
200 Hz between 0 and 180˚
Adjusts the phasing of the signal at
Phase 2
500 Hz between 0 and 180˚
Adjusts the phasing of the signal at
Phase 3
1.12 kHz between 0 and 180˚
Adjusts the phasing of the signal at 2.8
Phase 4
kHz between 0 and 180˚
Adjusts the phasing of the signal at 8
Phase 5
kHz between 0 and 180˚
Q 1/2 Q factor (parametric EQ)
Frequency 1 Adjusts mid frequency (parametric EQ)
Frequency 2 Adjusts mid frequency (parametric EQ)
dB 1 Adjusts the boost/cut at 200 Hz
dB 2 Adjusts the boost/cut at 400 Hz
dB 3 Adjusts the boost/cut at 800 Hz
dB 4 Adjusts the boost/cut at 1.6 kHz
dB 5 Adjusts the boost/cut at 3.15 kHz
dB 6 Adjusts the boost/cut at 6.3 kHz
Bass Adjusts the boost/cut at 100 Hz
Treble Adjusts the boost/cut at 12 kHz
Mix Used for gain correction
7