Publicidad
MRP-F320
SPEAKER
OUTPUT
(Rear side/Arrière/Parte trasera)
22
21
20
19
18
17
16
15
NOM
0.5V
OFF
MIN
MAX
GAIN
CHANNEL-1/2
(Front side/Avant/Parte delantera)
MRP-F200
SPEAKER
OUTPUT
(Rear side/Arrière/Parte trasera)
22
21
20
19
18
17
16
15
NOM
0.5V
MIN
MAX
GAIN
CHANNEL-1/2
(Front side/Avant/Parte delantera)
MRP-T130
SPEAKER
(Rear side/Arrière/Parte trasera)
18
17
16
15
All manuals and user guides at all-guides.com
+
–
+
–
+
CH-2
CH-1
30A
SUB W
–
–
+
–
+
CH-4
CH-3
FUSE
–
+
BRIDGED
6
14
NOM
NOM
100
0.5V
0.5V
75
55
HP
OFF
HP
OFF
ON
MIN
MAX
MIN
MAX
50
(80Hz)
(80Hz)
GAIN
GAIN
BASS BOOST
LP FILTER
FILTER
FILTER
CHANNEL-3/4
Sub woofer
–
+
–
+
CH-2
CH-1
25A
–
CH-4
+
–
CH-3
+
FUSE
–
BRIDGED
+
6
14
11
CH-1+3
CH-1
NOM
0.5V
OFF
HP
LP
OFF
ON
OFF
HP
LP
MIN
MAX
PRE
(80Hz)
(80Hz)
GAIN
BASS BOOST
OUT
FILTER
FILTER
CHANNEL-3/4
CH-2+4
CH-2
–
BRIDGED
+
+
+
–
CH-2
–
CH-1
20A
OUTPUT
FUSE
6
14
12
BATTERY REMOTE
GND
POWER SUPPLY
7
8
9
10
12
13
CH-1
CH-3
CH-1 2
3
4
140
+
(L)
170
–
200
INPUT
SPEAKER
(R)
LEVEL INPUT
CH-2
CH-4
BATTERY REMOTE
GND
POWER SUPPLY
7
8
9
10
12
13
CH-3
CH-1 2
3
4
+
(L)
–
INPUT
SPEAKER
(R)
LEVEL INPUT
CH-4
BATTERY REMOTE
GND
POWER SUPPLY
7
8
9
10
13
CONNECTIONS (Fig. 3 – F
Before making connections, be sure
power off to all audio components. C
yellow battery lead from the amp dir
positive (+) terminal of the vehicle's
not connect this lead to the fuse blo
To prevent external noise from en
audio system.
• Locate the unit and route the lead
cm away from the car harness.
• Keep the battery power leads as
from other leads as possible.
• Connect the ground lead securely
metal spot (remove the coating if
of the car chassis.
• If you add an optional noise supp
connect it as far away from the un
possible. Your Alpine dealer carri
Alpine noise suppressors, contac
further information.
• Your Alpine dealer knows best ab
prevention measures so consult y
for further information.
Speaker Output Terminal
6
The MRP-F320/MRP-F200/MRP-T1
sets of speaker outputs. Be sure to
correct speaker output connections
In the stereo mode, connect the righ
outputs to the right speaker and the
Connect the positive output to the p
speaker terminal and the negative to
In the bridged mode, connect the lef
the positive terminal on the speaker
right negative to the negative termin
speaker. Do not use the speaker (–)
a common lead between the left and
channels. Do not connect this lead t
vehicle's chassis.
NOTES:
1. Do not connect speaker leads tog
chassis ground.
2. In case of bridge connection, use
(sold separately). (Refer to the "B
Connections" below.)
Insulation Tube
7
Use for POWER SUPPLY (BATTER
GND) and SPEAKER OUTPUT term
Ground Lead (Black) (Sold Sep
8
Connect this lead securely to a clea
metal spot on the vehicle's chassis.
point to be a true ground by checkin
continuity between that point and th
(–) terminal of the vehicle's battery.
your audio components to the same
chassis to prevent ground loops.
Publicidad
