Oubleshooting; Chnical Specifications - Samsung DSB-A200C Instrucciones De Uso

2/27/04 3:22 PM Page 32
TROUBLESHOOTING
Possible cause Solution of the problem
D on Power cord Power cord plug in correctly
l; not plugged in correctly
ply
n the screen Receiver in Standby mode; Set receiver to "On";
Scart not connected tightly Check connection and correct;
to video output of television;
incorrect channel or video Check channel and video output and
output selected on television correct (TV instruction manual)
Audio cord connected Check connection and correct;
incorrectly;
Loudness level = 0; Increase loudness on television set;
Muting active Press the MUTE key
ol does not incorrect operation; Point remote control
ly towards the Receiver.
Batteries dead or inserted Replace batteries or insert correctly
incorrectly
uality Signal strength to low Check all wire connections. Check the
h in the "Auto Scanning" menu, correct
alignment of your antenna
or Message Antenna cable not connected Check connection and correct;
signal" or not tight;
LNB defective; Change LNB;
incorrect position of the Check position and correct,
satellite antenna; Check the signal strength in
LNB is set to "OFF" in the "Auto Scanning" menu
LNB Setting menu
or Message Satellite not yet set Scan of in "Automatic scanning"
or "Manual scanning" menu
."
or Messages: Smartcard: (depend on model)
the - not plugged in correctly; Check the Smartcard.
- not plugged in. "Insert the Smartcard."
the
mponent Selecting RGB video signal out, Select the video signal type to media
P ) or RGB YUV(YPbPr) video out turns off. setting menu : Composite, Composite +
r
RGB, Composite + YUV or S-Video.
Selecting composite+YUV video signal
out, YUV(YPbPr) video out turns on.
SAL
packaging material (e.g. Styrofoam) and the batteries must never be disposed of with
fuse. Please obtain appropriate information about the regulations in your community,
of all refuse in accordance with regulations at the separate locations provided.
GB-32
All manuals and user guides at all-guides.com
D I G I T A L S A T E L
TECHNICAL SPECIFICATIONS
Power supply
Type :
Input voltage :
Fuse rating :
Tuner
Freq. Range :
Input signal level :
Channel selection :
Input impedance :
Connector type :
LNB power control :
DiSEqC :
Demodulator
Type :
Symbol rate :
Inner FEC :
Outer FEC :
Video decoder
System decoding :
Profile and level :
Data rate :
Video formats :
Picture resolution :
Audio Decoder
System decoding :
Audio mode :
Sampling frequency :
L I T E R E C E I V E R
SMPS
AC 100-240V~, 50/60 Hz
250 V/T1.6AH
950 ~ 2150 MHz
-65 ~ -25 dBm
PLL frequency synthesizer
75 Ω unbalanced
F type female
13 V/18 V, 22 kHz tone
1.2 supported
QPSK DEMODULATION (DVB-S)
2 ~ 45 Ms/s
Viterbi Convolutional
Coding Rate - 1/2,2/3,3/4,5/6,7/8
Reed Solomon Coding (204,188), t = 8
MPEG 2 ISO/TEC 13818
(transport stream)
MPEG 2 MP@ML (4:2:2)
1~ 15 Mb/s
4:3 (normal) & 16:9 (widescreen)
720(H) x 576(V) x 50 fields/sec
MPEG 1 ISO/TEC 11172~3 layer I & II
mono, dual, stereo, joint stereo
32, 44.1, 48 kHz
GB-33