Troubleshooting - Denon DVD-5910 Instrucciones De Operación

ENGLISH

25 TROUBLESHOOTING

Check again before assuming the player is malfunctioning
2 Are all the connections correct ?
2 Are you following the instructions in the manual ?
2 Are the amplifier and speakers operating properly ?
If the DVD-5910 does not seem to be functioning properly, check the table below. If this does not solve the problem, the DVD-5910 may
be damaged. Turn off the power, unplug the power cord from the power outlet, and contact your store of purchase or nearest DENON
sales office.
Symptom
Power does not turn on.
Playback does not start when PLAY
button is pressed.
Playback stops immediately.
Picture does not appear.
Sound is not produced or sound quality
is poor.
Menu playback of video CD's is not
possible.
Picture is disturbed during the search
operation.
Buttons do not operate.
No subtitles are displayed.
Audio (or subtitle) language does not
switch.
Angle does not switch.
Playback does not start when the title is
selected.
The password for rating level has been
forgotten.
Reset all the setting to Factory
Preset.
The disc is not played with the audio or
subtitle language set as the default
setting.
Picture is not displayed in 4:3 (or 16:9).
Menu screen messages for the desired
language do not display.
• Plug the power supply cord securely into the power outlet.
• Is there condensation on the disc or player ? (Let stand for 1 or 2 hours.)
• Discs other than DVDs,SuperAudio CDs, video CDs and music CDs cannot be played.
• Disc is dirty. Wipe off the dirt.
• Check the connections.
• Check that VIDEO OUT has not been set to "VIDEO OUT:OFF" or "ALL OFF" for PURE
DIRECT MODE.
• Set the TV's input to "video".
• Check the connections.
• Properly set the input of the TV, stereo, etc.
• Check the "DIGITAL OUTPUT" and "COMPRESSION" settings.
• Digital signals cannot be output with Super audio CDs. Use analog or IEEE1394
connections.
• Area/layer of Super audio CD being played (MULTI/STEREO/CD) does not match amplifier
connections.
• When the video output setting at "PURE DIRECT" is set to "VIDEO OUT : OFF" or "ALL
OFF", no sound at HDMI connector.
• When a device not compatible with HDMI specification Ver. 1.1 is connected via an HDMI
connector, the audio signals of DVD audio discs copyright-protected by CPPM are not
output.
• Menu playback is not possible with anything but video CDs with playback control.
• Some disturbance is normal.
• Some operations are disabled for some discs.
• Subtitles are not displayed for DVDs not containing subtitles.
• Subtitles are turned off. Turn the subtitles setting on.
• The audio (or subtitle) language does not switch for discs which do not include multiple
audio (or subtitle) languages.
• For some discs the audio (or subtitle) language cannot be switched when the operation to
switch it is performed, but can be switched on the menu screens.
• The angle cannot be switched for DVDs which do not contain multiple angles. In some
cases multiple angles are only recorded for specific scenes.
• Check the "RATINGS" setting.
• While the player is in the stop mode, hold the player's SKIP
button down simultaneously and then hold the OPEN/CLOSE button down for longer than
3 seconds (until "INITIALIZE" disappears from the TV monitor).
The lock will be released and all default settings and picture settings will return to the
default values.
• The disc does not play with the selected audio or subtitle language if that audio or subtitle
language is not included on that DVD.
• Set the "TV ASPECT" default setting to the proper setting for the connected TV.
• Check the default setting for the disc language's menu language.
Check
button and the PLAY
9
ENGLISH
Page
11~21,
23
–
9
10
11~21
50, 51
–
11~21
–
40, 43,
44
15, 16,
18, 19
15, 16,
51
50, 51
20
61
–
61
–
30, 31
70, 71
74
72
45, 46
–
30~32
38
30~32
83