Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: F75161
Wrenches: 3/4, 21 mm, 22mm
Drill Bits: None
Note: All Fasteners Typical Both Sides of Vehicle
1
Qty. (4)
Bolt M14 X 2.00 X 40mm
2
Qty. (4)
Lock Washer 9/16
3
Qty. (4)
Flat Washer 9/16
4
Qty. (4)
Carriage Bolt 1/2-13 X 1-3/4
Note: Factory Installed Steel Step Bumper and Brackets Must Be Used In Conjunction with Hitch
1. Remove existing M14 bolts from end of each frame rail.
2. Lift receiver into position, locating rearmost slots in receiver under existing weldnuts in vehicle frame.
3. Install new M14 bolts through receiver into weldnuts in vehicle frame and into step bumper.
4. Install remaining fasteners as shown.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2002, 2006 Cequent Towing Products
Installation Instructions
Chevrolet Silverado Pickup
GMC Sierra Pickup
(Vehicles with amber turn signals)
6
7
Frame
Bumper
Tighten M14 CL10.9 fasteners with torque wrench to 115 Lb.-Ft. (156 N*M)
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
Hitch type
Weight Distributing
4
Weight Carrying
Ball Mount
5
Wiring Access Location: PU3
Existing weldnut typical both sides
3
2
1
321
5
Qty. (4)
Spacer
6
Qty. (4)
Conical Washer 1/2
7
Qty. (4)
Hex Nut 1/2-13
Sheet 1 of 3
N75161
Part Numbers:
75161
Max Gross
Trailer WT (LB)
7500 (3405 Kg)
6000 (2724 Kg)
Factory installed bumper bracket
- Typical both sides
5-18-06
Form: F205 Rev A 5-6-05
Max Tongue
WT (LB)
750 (341 Kg)
600 (272 Kg)
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products 75161
Resumen de contenidos para Cequent Towing Products 75161
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2002, 2006 Cequent Towing Products Sheet 1 of 3 N75161 5-18-06 Rev.
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2002, 2006 Cequent Towing Products Feuille 2 de 3 N75161 5-18-06 Rev.
- Página 3 No corte el acceso o los orificios del accesorio con soplete. Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. 2002, 2006 Cequent Towing Products Hoja 3 de 3 N75161 5-18-06 Rev.