Care And Maintenance - Black and Decker BCS15B Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

SMART CHARGE
1. Set up the unit as described in the "Setting Up the Unit" section, selecting the Smart Charge function before connecting the
clamps to the battery.
2. When the unit is done analyzing the battery, it will begin the recharging process. The LCD will then display the battery
voltage (for example: CHARGING / 12.5 VOLTS). As the battery charges, the arrow on the Charging Gauge will move
indicating the current percent of charge in the battery, from the red zone (0-25% charged) toward the green zone (90-100%
charged).
3. When the unit is fully charged, the LCD displays BATTERY IS FULLY CHARGED. The status LED will light green.
4. Disconnect first the AC cord, then the clamps to shut the unit off. Observe the "Important Safety Instructions" at the front of
this manual when disconnecting.
ALTERNATOR CHECK
Part 1
No Load (Turn OFF all vehicle's accessories): The battery must be fully charged before testing the alternator. Run the engine
long enough to achieve normal idle speed and verify there is a no-load voltage.
1. Set up the unit as described in the "Setting Up the Unit" section, selecting the Alternator Check function before connecting
the clamps to the battery. ANALYZING ALTERNATOR will display on the LCD.
2. Once the unit has finished checking, the LCD will display either ALTERNATOR GOOD (the status LED will light green) or
ALTERNATOR BAD OR ENGINE NOT RUNNING (the status LED will light red).
Part 2
Under Load (Accessories ON): Next, load the alternator by turning on as many accessories as possible (except for A/C and
DEFROST) and repeat the above four steps.
After completing both alternator checks, disconnect the AC cord and clamps, observing the "Important Safety Instructions" at
the front of this manual.
If the first alternator check indicates a good alternator and the second indicates the alternator is not good, the problem could
stem from: loose fan belts, an intermittent diode failure or possibly bad connections between the battery and alternator and/or
ground.
ALTERNATOR BAD OR ENGINE NOT RUNNING may display because someone has added a number of accessory loads on the
charging system, thereby increasing current demand from the alternator. MAKE SURE THAT THE ALTERNATOR IS RATED TO
SUPPORT THE APPLICATION.
Note: This check may not be accurate for every make, manufacturer and model of vehicle.
Check only 12 volt systems.
TROUBLESHOOTING
General
The unit will turn on automatically after being properly connected to the battery. If it does not come on, either it is not connected
properly to the terminals or the voltage of the battery to be serviced is too low (below 3 volts).
Smart Charge Fault Condition Messages
If there is a problem with the connections or battery, the LCD will display the appropriate fault condition message, as follows:
Fault Message
Explanation/Recommendation
CHECK CLAMP CONNECTION TO THE
When this message appears, the most common cause is poor connection to
BATTERY
battery.
• Observing the "Important Safety Instructions" at the front of this manual,
disconnect AC cord and clamps, clean battery terminal and reconnect.
• If the situation persists, we recommend taking your battery to a certified
automotive service center for evaluation.
REVERSE CLAMPS ON BATTERY
The connections to the battery's positive and negative terminals are incorrect.
(Status LED lights red and continuous
Observing the "Important Safety Instructions" at the front of this manual,
warning tone sounds)
disconnect AC cord and clamps and reconnect to battery with correct polarity.
REPLACE OR SERVICE BATTERY
The battery being charged either has an internal open or shorted cell or is highly
sulfated and cannot accept normal charge current. We recommend taking your
battery to a certified automotive service center for evaluation.
COOL DOWN CYCLE
The ventilation grill that prevents the air from flowing in and out of the charger
(Status LED lights red)
may be blocked.
• Observing the "Important Safety Instructions" at the front of this manual,
disconnect AC cord and clamps, allow the unit to cool for 30 minutes and
reconnect.
• Make sure there is ample ventilation before resuming operation.
Charging a Very Cold Battery
If the battery to be charged is very cold (in temperatures below freezing — 0°C/ 32°F), it cannot accept a high rate of charge.
The battery will accept a higher charge rate as it warms. NEVER ATTEMPT TO CHARGE A FROZEN BATTERY.
6
Fault Message
Explanation/Recommendation
OVERTIME CONDITION
The charging cycle has exceeded 18 hours. This may occur under the following
conditions:
• Battery (or batteries, in the case of a battery bank) being charged has/have a
capacity over 270 Ah.
Disconnect charger from AC outlet and reconnect to start a another 18-hour
cycle. Repeat as necessary according to capacity.
• If the battery capacity is ≤ 270 Ah and this fault message appears, the battery
being charged is possibly defective.
We recommend taking your battery to a certified automotive service center for
service or replacement.
Alternator Check Fault Condition Messages
If there is a problem with the connections or battery, the LCD will display the appropriate fault condition message, as follows:
Fault Message
Explanation/Recommendation
CHECK CLAMP CONNECTION TO THE
When this message appears, the most common cause is poor connection to
BATTERY
battery.
• Observing the "Important Safety Instructions" at the front of this manual,
disconnect AC cord and clamps, clean battery terminal and reconnect.
• If the situation persists, we recommend taking your battery to a certified
automotive service center for evaluation.
REVERSE CLAMPS ON BATTERY
The connections to the battery's positive and negative terminals are incorrect.
(Status LED lights red and continuous
Observing the "Important Safety Instructions" at the front of this manual,
warning tone sounds)
disconnect AC cord and clamps and reconnect to battery with correct polarity.

CARE AND MAINTENANCE

With proper care and minimal maintenance, this unit will provide years of dependable service. For maximum performance,
manufacturer recommends:
• After each use, clean the battery charger clamps — be sure to remove any battery fluid that will cause corrosion of the
clamps.
• Clean the outside case of the charger with a soft cloth and, if necessary, mild soap solution.
• Do not allow liquid to enter the charger. Do not operate when charger is wet.
• Keep the charger cords loosely coiled during storage to prevent damage to the cords.
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY OR PROPERTY DAMAGE:
• Do not use charger if cords or clamps have been damaged in any way — call Technical Support toll-free at 1-800-544-6986.
• There are no user-serviceable parts in this unit.
• Do not open the unit. In the event of malfunction, it must be returned to manufacturer for professional testing and repair.
Opening the unit will void the manufacturer's warranty.
ACCESSORIES
Recommended accessories for use with your charger are available from your local dealer or authorized service center. If you
need assistance regarding accessories, please call: 1-800-544-6986.
WARNING: The use of any accessory not recommended for use with this charger could be hazardous.
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool
service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location
nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1-800-544-
6986 or visit www.blackanddecker.com.
FULL FIVE-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for five years against any defects in material or workmanship. The defective
product will be replaced or repaired at no charge in either of two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that
the store is a participating retailer). Returns should be made within the time period of the retailer's policy for exchanges (usually
30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy
regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or authorized Service Center for repair or
replacement at our option. Proof of purchase may be required. Black & Decker owned and authorized Service Centers are listed
under "Tools-Electric" in the yellow pages of the phone directory and on our website www.blackanddecker.com.
This warranty does not apply to accessories. This warranty gives you specific legal rights and you may have other rights which
vary from state to state or province to province. Should you have any questions, contact the manager of your nearest Black &
Decker Service Center. This product is not intended for commercial use.
FREE WARNING LABEL REPLACEMENT: If your warning labels become illegible or are missing, call 1-800-544-6986 for a free
replacement.
7

Publicidad

Tabla de contenido
loading

Tabla de contenido