Operating manual BDC1330 DBP/LPP
Maintenance, cleaning and
decontamination
WARNING!
To guarantee the safety level of the vacuum
cleaner, only original spare parts supplied by the
manufacturer should be used.
WARNING!
The precautions described below must be taken
during all the maintenance operations, including
cleaning and replacing of the main and HEPA filters.
WARNING!
The maintenance, cleaning and decontamination
operations must only be performed with the
vacuum cleaner turned off with switch (7 - Fig. 5)
and the plug disconnected from the power socket.
It is absolutely forbidden to perform maintenance
with the plug connected to the socket.
Danger of electric shock!
■
If the user is performing the maintenance operations,
the vacuum cleaner must be disassembled, cleaned
and overhauled as far as reasonably possible without
hazards for the maintenance personnel or other people.
The suitable precautions include decontamination before
disassembling the vacuum cleaner, adequate filtered
ventilation of the exhaust air from the room in which
it is disassembled, cleaning the maintenance area and
suitable personal protection.
■
A check must be carried out by the manufacturer or
the personnel of the same at least once a year. For
example: check the air filters to find out whether the
air-tightness of the vacuum cleaner has been impaired
in any way and make sure the electric control panel
operates correctly.
WARNING!
The procedures for servicing and emptying the
vacuum cleaner including removing the dust
container, must only be performed by specialised
personnel wearing protective clothing. Do not use
without the complete filter system in place.
Cartridge and absolute filter
disassembly and replacement
WARNING!
When performing the filter replacement it is
necessary to:
■
work with care and avoid spilling the vacuumed
dust and/or material;
■
place the disassembled and/or replaced filter
in a sealed plastic bag;
■
close the bag hermetically;
■
dispose of the filter in accordance with the
laws in force.
WARNING!
Filter replacement is a serious matter. The
filter must be replaced with one of identical
characteristics, filtering surface and category.
Otherwise the vacuum cleaner will not operate
correctly.
WARNING!
Take care not to raise dust when this operation is
carried out. Wear a P3 mask and other protective
clothing plus protective gloves (DPI) suited to the
hazardous nature of the dust collected, refer to the
laws in force.
WARNING!
Reassemble with care to avoid trapping your hands
between the vacuum unit and the container. Use
gloves that provide protection against mechanical
risks (EN 388) with a level of protection CAT. II.
Filter cartridge replacement
Figure 11
1.
Vacuuming unit
2.
Locking lever
3.
Ring
4.
Compressed air hose
5.
Electric cable
6.
Locking lever
7.
Cover
8.
Filter cartridge support
9.
Filter cartridge
10.
Filter cartridge fixing nut
11.
Electric connector
12.
Electrical plug
Before proceeding with these operations, turn off the vacuum
cleaner and remove the plug from the power socket.
■
Use the lever (2) to release vacuuming unit (1), remove
the plug (12) connected to the electric system box and
disconnect the compressed air hose (4), then remove the
vacuuming unit (1) from the vacuum cleaner by pulling it
up and out.
■
Disconnect the compressed air hose (4) by releasing its
quick-fit coupling.
■
Disconnect the electric cable (5) by releasing the connector
(11).
■
Use the lever (6) to remove the cover (7).
■
Remove the support (8) with the filter cartridges.
■
Remove the filters cartridge (9) by unscrewing the fixing
nuts (10).
■
Assemble the new filter cartridges and proceed in the
reverse order of removal to install all the components,
making sure that the previously disconnected electrical
and pneumatic connections have been reconnected.
When reassembling, turn the cover until the
electropneumatic device is in the right position for the
cartridge support.
■
Dispose of the old filter cartridges according to the laws
in force.
11/14
info@blastrac.eu
GB