Publicidad
Idiomas disponibles
Idiomas disponibles
c)
Power supply scheme for card reader
1
1.
Access controller
After connecting the wires and making sure they have been
connected in accordance with the above diagrams, fasten
the front panel with screws to the rear wall of the device.
Only now can you turn on the power.
3.3. DEVICE USE
3.3.1. CONTROLS
Action
LED indi-
Finger-
Acoustic
cator
print
signal
sensor
Restore facto-
orange
off
Double
ry settings
short beep
Sleeping
red slowly
off
-
mode
blinking
Standby
red slowly
on
-
mode
blinking
Acceptance
-
-
Single long
of keys
beep
Enter pro-
red
off
Single long
gramming
beep
mode
Exit program-
red slowly
on
Single long
ming mode
blinking
beep
Action incor-
-
-
Triple short
rect
beep
Opening
green
off
Single long
door
beep
EN
3.3.2 PROGRAM THE DEVICE
CAUTION: the individual card number is printed on the card
and consists of the numbers marked below (only an example
combination shown):
A.
Enter programming mode
On the remote control, press the following buttons in turn:
* + administrator code + #
NOTE! The default admin access code is „888888".
After entering the programming mode all the subsequent
setting operations (B - H) must be performed.
B.
Changing admin code
Press the following buttons in turn on the remote control:
0 + new administrator code + # + new administrator code
+ #
NOTE! The access code must contain between 6 and 8 digits
C.
Adding users
•
Add users continuously
Press:
1 + 2 x press user's finger on the reader + #
OR
1 + card scan + #
OR
1 + Enter the card number on the remote keypad (8 digits)
+ #
AND
#
NOTE! With 200 prints, the IDs are 3-200 (1 and 2 is reserved
for the administrator). With 500 users, IDs are from 1001-
1500 (1000 is reserved for the administrator). With 1000
prints and 2000 cards, IDs are 3-1000 and the cards 1001-
3000, respectively.
•
Adding users by ID number
Press:
1 + ID number + # + + 2 x user fingerprint scan on reader
+ # ...
OR
1 + ID number + # + card scan + # ...
OR
1 + ID number + # + card number (8 digits) + # ...
AND
#
NOTE! „ID 1" means adding is approved by the administrator's
fingerprint and ID 2 means deletion is approved by the
administrator's fingerprint. Pressing „#" means confirming
the operation, while double press of „#" means completion
of the programming operation. Pressing „*" means entering
the programming mode.
•
Add users using the admin fingerprint or admin card
Admin's fingerprint scan
OR
Add User card scan + 2x first user's fingerprint scan + 2x
second user's fingerprint scan
OR
Scan of the first and second cards
OR
10
Admin's fingerprint scan
OR
Add User card scan
AND
* (exit programming mode)
D.
Deleting users
•
Delete users using fingerprint / card / card number
Press:
2 + 2x user's fingerprint scan + #
OR
Delete User card scan + #
OR
Card number (8 digits) + #
AND
#
•
Delete users by ID number
Press:
2 + ID number 1 + # + ID number 2 + # ...
AND
#
•
Delete all users
Press:
20000 + #
NOTE! All users along with their fingerprint scans will be
deleted but the administrator card will be remembered.
•
Delete users using the admin's fingerprint or admin's
card.
Press:
Admin's fingerprint scan
OR
Delete User card scan
AND
2x first user's fingerprint scan + second user's fingerprint
scan ... first card scan + second card scan ...
AND
Admin's fingerprint scan
OR
Delete User card scan
AND
* (exit programming mode)
E.
Setting the building code
Press
3 + 0-255 + #
NOTE! The building code should be set if the device is used
as a card reader. The building code together with the ID
number make the virtual card number. During the fingerprint
scan the data is transmitted via the Wiegand 26 protocol.
For example, if the building code is 255 and the fingerprint
scan ID is 3, the virtual card number is 255,00003. This
function applies to the ID number only for simulated 8
decimal digits. The virtual card number is displayed on the
device in the Wiegand 26 format.
F.
Setting the delay time of door lock opening
5 + 0-99s + #
NOTE! The factory setting is 5 seconds.
G.
Setting the door open sensor
•
Disable the sensor (factory setting)
Press:
6 + 0 + #
EN
•
Enable the sensor
Press:
6 + 1 + #
NOTE! If the door is not closed after opening, a reminder
signal will sound after 1 minute. The signal stops after the
door is closed. The acoustic signal will also be activated if the
door is not opened within 120 seconds of unlocking or if an
attempt is made to force it open.
H.
Setting the security mode
•
Normal mode (factory setting)
Press:
7 + 0 + #
•
Lock mode
Press:
7 + 1 + #
NOTE! After 10 unsuccessful fingerprint or card scan
attempts, the device will be locked for 10 minutes.
3.3.3. OPERATING THE DEVICE
A.
Opening with a fingerprint scan
Place the finger previously scanned on the device on the
print reader to unlock the door. NOTE! Keep your finger on
the reader until a signal sounds and a visual signal lights up
to indicate the door is unlocked - see 3.3.1.
B.
Opening with a card
Present a valid card to the reader to unlock the door.
NOTE! Place the card as close as possible to the reader and
wait for a visual and audible unlock signal - see 3.3.1.
C.
Replacing the remote control battery
If the device responds poorly or does not respond to remote
control, check the battery status.
At the bottom of the remote control there is a battery
drawer. Pry it open and pull the recess visible on it (e.g.
with a fingernail) to pull the drawer and battery out. When
installing a new battery in the drawer, pay attention to
the correct polarity. Slide the battery drawer back into the
remote control until it clicks.
NOTE! The remote control and battery drawer are
constructed in such a way as to make it impossible to install
the battery with reversed polarity.
3.4. CLEANING AND MAINTENANCE
a)
Do not spray the device with a water jet or submerge
it in water.
b)
Clean the vents with a brush and compressed air.
c)
The device must be regularly inspected to check its
technical efficiency and spot any damage.
d)
Use a soft cloth for cleaning.
e)
Do not leave the battery in the device if it will not be
used for a longer period of time.
11
Publicidad
