Philips AZ-2050 Guia De Inicio Rapido página 10

Ocultar thumbs Ver también para AZ-2050:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

CASSETTE RECORDER
CD Synchro Start recording
1 Select CD function.
2 Insert a CD and if desired, program track numbers.
3 Open the cassette door.
4 Insert a suitable tape into the cassette deck and
close the door.
5 Press RECORD 0 to start recording.
– Playing of the CD program starts automatically
from the beginning of the program. You don't
need to start the CD player separately.
™ To select and record a particular passage within
a CD track:
• Press ∞ or §. Release the control when you
recognize the passage you want.
• To pause CD playback, press 2;.
• Recording starts from this exact point in the
track when you press RECORD 0.
6 To pause recording, press PAUSE ;.
Press PAUSE ; again to resume recording.
7 To stop recording, press STOP/OPEN 9/.
Recording from the Radio
1 Tune to the desired radio station (see Tuning to
radio stations).
2 Follow steps 3-7, under Synchro Start CD
recording.
All manuals and user guides at all-guides.com
MAINTENANCE & SAFETY
MAINTENANCE & SAFETY
CD player and CD handling (See 6)
• If the CD player cannot read CDs correctly, use a
cleaning CD to clean the lens before taking the set
to repair.
• The lens of the CD player should never be touched!
• Sudden changes in the surrounding temperature
can cause condensation on the lens of your CD
player. Playing a CD is then not possible. Do not
attempt to clean the lens but leave the set in a
warm environment until the moisture evaporates.
• Always close the CD door to avoid dust on the
lens.
• To clean the CD, wipe in a straight line from the
center towards the edge using a soft, lint-free
cloth. Do not use cleaning agents as they may
damage the disc.
• Never write on a CD or attach any stickers to it.
Safety Information
• Don't expose the set, batteries, CDs or cassettes to
humidity, rain, sand or excessive heat.
• Clean the set with a dry cloth. Don't use any
cleaning agents containing alcohol, ammonia,
benzene or abrasives as these may harm the set.
• Place the set on a hard and flat surface so that the
system does not tilt. Make sure there is good
ventilation to prevent the set overheating.
• The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
Tape deck maintenance (See 7)
To ensure quality recording and playback of the tape
deck, clean parts A, B and C as shown, once a
month. Use a cotton bud slightly moistened with
alcohol or a special head cleaning fluid to clean the
deck.
1 Open the cassette door.
2 Press PLAY 2 and clean the roller C.
3 Press PAUSE ; and clean the heads A, and the
capstan B.
4 After cleaning, press STOP/OPEN 9/.
TROUBLESHOOTING
WARNING
Do not open the set as there is a risk of electric shock! Under no circums
repair the set yourself, as this will invalidate the warranty.
If a fault occurs, first check the points listed below before taking the set for repai
If you are unable to remedy a problem by following these hints, consult your deale
Remote control does not function properly
(AZ 2055 only)
– Batteries exhausted/ incorrectly inserted
• Insert (fresh) batteries correctly
– Distance/ angle between the set too large
• Reduce the distance/ angle
No sound /power
– Volume not adjusted
• Adjust the VOLUME
– Power cord not securely connected
• Connect the AC power cord properly
– Batteries dead/ incorrectly inserted
• Insert (fresh) batteries correctly
– Headphones connected to the set
• Disconnect headphones
Severe radio hum or noise
– Electrical interference: set too close to TV, VCR or
computer
• Increase the distance
Poor radio reception
– Weak radio signal
• FM: Adjust the FM telescopic aerial
Environmental information
We have done our best to reduce the packaging and make it easy to separate int
expandable polystyrene, polyethylene.
Your set consists of materials which can be recycled if disassembled by a special
the local regulations regarding the disposal of packaging, dead batteries and old e
Poor cassette sound q
– Dust and dirt on the h
• Clean deck parts, see
– Use of incompatible ca
(METAL or CHROME)
• Only use NORMAL (IEC
Recording does not w
– Cassette tab(s) may be
• Apply adhesive tape o
– CD badly scratched or
• Replace/ clean CD, se
– Laser lens steamed up
• Wait until lens has cle
indicatio
– CD-R(W) is blank/ not
• Use a finalized CD-R(W
indicatio
– CD-ROM disc inserted
CD contains non-audio
• Use CD Audio discs on
press ∞ or § once o
track instead of the da
The CD skips tracks
– CD damaged or dirty
• Replace or clean CD
– SHUFFLE or PROGRAM
• Switch off SHUFFLE /

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Az-2055

Tabla de contenido