Replacing The Crossfader; Specifications - Denon DN-X800 Manual De Instrucciones

REPLACING THE CROSSFADER

7
The Crossfader may be removed without any disassembly of the DN-X800 itself, and may be performed while the unit is operating
with no interruption of the audio signal.
1. Remove the two (2) outer screws attaching the crossfader assembly to the front panel.
2. Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.
3. Install the replacement assembly by reversing the above instructions.

SPECIFICATIONS

8
GENERAL
Dimensions: 482 (W) x 105 (H) x 177 (D) mm (without feet)
Installation: 19-inch rack mountable 4U
Mass: 5.5 kg
Power supply: 230 V AC ±10%, 50 Hz
220 V AC ±10%, 50 Hz
Power consumption: 26 W
Environmental conditions: Operational temperature:
Operational humidity:
Storage temperature:
AUDIO SECTION
Input Sensitivity & Impedance:
Main Mic -54 dBV (2.0 mV)
Aux Mic -60 dBV (1.0 mV)
Effect (Return) -14 dBV (200 mV)
3-Phono -50 dBV (3.0 mV)
8-Line -14 dBV (200 mV)
Output level & Impedance:
Main (Balanced) 4 dBm (1.23 V)
Main (Unbalanced) 0 dBV (1.0V)
Zone (Balanced) 4 dBm (1.23 V)
Booth (RCA) 6 dBV (2.0 V)
Tape (RCA) -10 dBV (316 mV)
Effect (Send) -14 dBV (200 mV)
Subwoofer -2 dBV (800 mV)
Headphone -4 dBV (630 mV)
Frequency Response:
Line 20 to 20 kHz ±2 dB
Phono 20 to 20 kHz RIAA ±2 dB
Mic 20 to 20 kHz ±2 dB
Signal to Noise ratio:
Line 80 dB 0 dBm, 1 kHz, EQ flat
Phono 75 dB 0 dBm, 1 kHz, EQ flat
Main Mic 65 dB 0 dBm, 1 kHz, EQ flat
Total harmonic distortion rate:
Line Below 0.05%
Phono Below 0.05%
Cross talk: Over 70 dB
Channel equalizer:
Hi +10 dB, -26 dB (13 kHz)
Mid +10 dB, -26 dB (1 kHz)
Low +10 dB, -26 dB (100 Hz)
Microphone equalizer:
Hi +12 dB, -12 dB (10 kHz)
Mid +12 dB, -12 dB (1 kHz)
Low +12 dB, -12 dB (100 Hz)
Digital input:
Input sensitivity -20 dBV (100 mV)
Signal format SPDIF
0.5 Vp-p 75 Ω/ohms
Output level
Digital output:
Signal format IEC958 Type II
0.5 Vp-p 75 Ω/ohms
Output level
Output signal level -6 dB
Specifications and design are subject to change without notice for purpose of improvement.
(Europe model)
(China model)
5 to 35°C (41 to 95°F)
25 to 85% (no condensation)
-20 to 60°C (4 to 140°F)
10 kΩ/kohms
10 kΩ/kohms
50 kΩ/kohms
50 kΩ/kohms
50 kΩ/kohms
600 Ω/ohms load
1 kΩ/kohms
600 Ω/ohms load
1 kΩ/kohms
1 kΩ/kohms
1 kΩ/kohms
1 kΩ/kohms
150 Ω/ohms
ENGLISH
9