Specific Safety Rules For Wheel; Features - Urrea EHT10 Manual De Usuario

before making any adjustments, changing ac-
cessories or storing the tool. This preventive
safety measures reduce the risk of accidental
starting of the tool.
When the power tool is not in use, store it out
of the reach of children, and do not allow in-
dividuals who are not familiar with the power
tool or these instructions to operate it. Power
tools are dangerous in the hands on untrained
users.
Maintain the power tool. Check for misalign-
ment or binding of moving parts, broken parts,
and any other condition that may affect the
operation of the power tool. If it is damaged,
have it repaired before using. Many accidents
are caused by poorly maintained power tools.
Check for misalignment or bonding of moving
parts, breakage parts, and any other condition
that may affect the tools operation. If you find
a damaged tool, take it to service before use it.
Use only accessories that are recommended by
the manufacturer of your model. Suitable ac-
cessories for one tool, may become hazardous
when are used on another tool.
Keep cutting tools, sharpened and clean. Cut-
ting tools in good condition with sharpened
edges, are less likely to stuck in workpieces or
easier to control.
Is recommendable to use a safety device suit-
able, such a thermal and diferential switch
when you are using an electric equipment.
SERVICE
Tool service must be perfomed only by quali-
fied repair personnel. Service or maintenance
performed by unqualified personnel could re-
sult in a risk of injury.
SPECIFIC SAFETY RULES FOR
TWO POST LIFTS
WARNING: This instruction manual is the
important part of the product. Please read it
carefully and keep It properly.
• Do not install this lift on an asphalt surface.
• Do not install this lift on any surface other
than concrete confirming to minimum specifi-
cations.
• Do not install this lift over expansion joints or
cracks. Check with an engineer.
• Do not install this lift on a second floor with a
basement beneath without written authoriza-
E N G L I S H •
tion from an engineer
• This lift is only as good as the floor you put
it on. A good level floor is recommended for
proper lift installation and operation. Concrete
should be a minimum of 4" thick and 3,OOOpsi
tensile strength with steal or fiber mesh rein-
forcement.
• The lift is intended to raise the entire body
of the vehicle. Do not attempt to lift only part
of the vehicle. Improper use of this equipment
could result in damage to the lift, yourself or
other property.
• The lift is intended to lift vehicles only. It is
not designed to lift any person or equipment
containing people.
• Users of this equipment should be qualified,
responsible and should follow the operation
and safety gUidelines set forth in this manual.
Improper installation can cause damage or in-
jury.
Manufacturer will not assume liability for loss
or damage of any kind, expressed or implied,
resulting from improper installation or use of
this product. Read the installation and opera-
tion manual in its entirety before attempting
to install the lift.

FEATURES

This Lift is a 10000 lb. capacity, 2-Post Lift with
a latch system.
The safety latch is in contact with the latch
rack as the lift ascends and drops into place.
The safety latch engages in rack at 3" incre-
ments beginning about 16"frorn the ground.
The latch must be manually disengaged for the
lift to descend. The latch is released by raising
the latch up off the latch rack and pulling the
release cable. Once the raise button is pressed,
the latch will automatically re-engage after ap-
proximately 3" of travel.
Heavy bearings and heavy-duty leaf chains are
used throughout the lift. The work is done
with the heavy-duty chain connected to a 2 \/2"
cylinder, driven by a hydraulic pump capable of
providing 3,OOOpsi.
Please read the Safety Procedures and Opera-
tion Instructions in this manual before operat-
U se r 's m a nu a l
13