Tips And Tricks; Cleaning & Maintenance - Metabo SB 710 Manual Original

17027063_1110 SB_Bauk10.book Seite 14 Dienstag, 23. November 2010 2:03 14
ENG ENGLISH
Opening the chuck: Grip the retaining ring and,
using the other hand, rotate the sleeve in the direc-
tion of the arrow -1-.
Clamping the tool: Insert tool -2- as far as it will
go. Grip the retaining ring and, using the other
hand, firmly rotate the sleeve as far as it will go in
the direction of the arrow -3-.
8.10 Tool change with Plus (5) chuck
See illustrations B on page 3.
Opening the drill chuck:
Grip the retaining ring and, using the other hand,
rotate the sleeve in the direction of the arrow -1-.
The grating sound (depending on function) which
may be heard after opening the drill chuck is
stopped by turning the sleeve in the opposite
direction.
If the chuck is very tightly secured, disconnect
from mains. Hold the chuck using an open-end
spanner at the flats on its head, and turn the sleeve
vigourously in the direction of the arrow -1-.
Clamping the tool
- Insert the tool -2- as far as it will go.
- Grip the retaining ring and, using the other hand,
rotate the sleeve in the direction of the arrow -3-
until the mechanical resistance which can be felt
is overcome.
- Caution! The tool is not yet fully clamped!
Keep turning the sleeve (it must "click" when
turning) until it cannot be turned any further -
only now is the tool securely clamped.
In the case of a soft tool shank, retightening may
be required after a short period of drilling.
8.11 Tool change with a geared chuck (4)
See illustrations C on page 3.
Opening the chuck: Opening a geared chuck with
the chuck key -1-.
Clamping the tool: Insert tool -2- as far as it will
go and tighten equally in all 3 bores using the
chuck key -3-.
8.12 Unscrewing the chuck
Futuro Top keyless chuck (6)
(see illustration X on second to last page)
Unscrew the drill chuck with two open-end span-
ners.
Futuro Plus keyless chuck (5)
(see illustrations Y on second to last page)
14
All manuals and user guides at all-guides.com
Undo the locking screw. Caution! Left-handed
thread!
Grip the drill spindle using an open-end spanner.
Insert an Allen key into the chuck, tap on it with a
rubber hammer to loosen the chuck, and then
unscrew.
Geared chuck (4)
(see illustrations Z on second to last page)
Undo the locking screw. Caution! Left-handed
thread!
Grip the drill spindle using an open-end spanner.
Insert the chuck key into the chuck, tap on it with
a rubber hammer to loosen the chuck, and then
unscrew.
In the case of deep bores pull the drill bit out of the
bore from time to time in order to remove the stone
dust or shavings.
Drill tiles and other brittle materials without impact.
Switch on the impulse function (SBE 900 Impuls
only) for drilling without a centre punch.
The drill chuck can be removed for screwdriving.
Insert screwdriver bit directly into the spindle's
hexagon socket. If a bit clamping bush (order no.
6.31281) is fitted, the screwdriver bit is held in
position.
For thread tapping (except SB 710), apply some oil
to the tap. Select a low speed and the first gear.
Start cutting in clockwise direction, stop and turn
out in counter-clockwise direction.
Cleaning the keyless chuck:
After prolonged use hold the chuck vertically, with
the opening facing down, and fully open and close
it several times. The dust collected falls from the
opening. Regular use of cleaning spray on the jaws
and jaw openings is recommended.
If it is not possible to press in the trigger (13), check
if the rotation selector switch (11) is fully at position
R or L (except SB 710).
SBE 900 Impuls: If the setting wheel (9) is moved
from impulse function to torque control while the
machine is switched on, the machine switches off
automatically. Switch the machine off and then
back on again.
Electronic signal display (10)
Rapid flashing - restart protection
(SBE 1000, SBE 1100 Plus)

9 Tips and Tricks

10 Cleaning, Maintenance
11 Troubleshooting