Removing The Collected Water; Care And Maintenance; Care And Cleaning Of The Dehumidifier - INVENTOR PR1-ION10L Manual Del Usuario

OPERATING THE UNIT

Removing the collected water

There are two ways to remove collected water.
1. Use the bucket
• When the unit is off, if the bucket is full, the unit will
beep 8 times and the Full indicator light will flash, the
digital display shows P2.
• When the unit is on, if the bucket is full, the compressor
turns off and the fan turns off after 30 seconds for drying
the water of the condenser, then the unit will beep 8
times and the Full indicator light will flash, the digital
display shows P2.
• Slowly pull out the bucket. Grip the left and right
handles securely, and carefully pull out straight so
the water does not spill. Do not put the tank on the floor
because the bottom of the bucket is uneven. Doing so
will cause the bucket to fall and the water to spill.
• Throw away the water and replace the bucket. The
bucket must be in place and securely seated for the
dehumidifier to operate.
• The machine will re-start when the bucket is restored
in its correct position.
NOTES:
• When you remove the bucket, do not touch any parts
inside of the unit. Doing so may damage the product.
• Be sure to push the bucket gently all the way into the
unit. Banging the bucket against anything or failing to
push it in securely may cause the unit not to operate.
• When you remove the bucket, if there is some water in
the unit you must dry it.
2. Continuous draining.
• Water can be automatically emptied into a floor
drain by attaching the unit with a water hose
(not included).
• Pull the rubber plug from the back drain
hose outlet. Attach a drain hose(ID=13.5mm)
and lead it to the floor drain or a suitable
drainage facility(see Fig.7).
• Make sure the hose is secure so there are no leaks.
• Direct the hose toward the drain, making sure that
there are no kinks that will stop the warter flow.
• Place the end of the hose into the drain and make sure
the end of the hose is level or sloping downward allowing
the water to flow smoothly. Never have the water flow
upwards.
• Select the desired humidity setting and fan speed
on the unit for continuous draining to start.
NOTE: When the continuous drain feature
is not being used, remove the drain hose
fromthe outlet.
1. Pull out the bucket a little.
Fig.5
2. Hold both sides of the bucket
with even strength, and pull it
out from the unit.
Fig.6
3. Pour the water out.
Remove the
rubber plug
Attach the hose
Fig.7
to the drain
hose outlet.

Care and cleaning of the dehumidifier

Turn the dehumidifier off and remove the plug
from the wall outlet before cleaning.
1 . Clean the Grille and Case
Use water and a mild detergent. Do not use bleach
or abrasives.
Do not splash water directly onto the main unit. Doing
so may cause an electrical shock, cause the insulation
to deteriorate, or cause the unit to rust.
The air intake and outlet grilles get soiled easily, so use
a vacuumattachment or brush to clean.
2 . Clean the bucket
Every few weeks, clean the bucket to prevent growth of mold,
mildew and bacteria. Partially fill the bucket with clean water
and add a little mild detergent. Swish it around in the bucket,
empty and rinse.
NOTE: Do not use a dishwasher to clean the bucket.
After cleaning, the bucket must be in place and securely
seated for the dehumidifier to operate.
3 . Clean the air filter
The air filter behind the front grille should be
checked and cleaned at least every 30 days
or more often if necessary
NOTE: DO NOT RINSE OR PUT THE FILTER
INANAUTOMATIC DISHWASHER.
To remove:
Grip the tab on the filter and pull it upward, then
pull it out as shown in Fig.8.
Clean the filter with warm, soapy water. Rinse and
let the filter dry before replacing it. Do not clean the
filter in a dishwasher.
To attach:
Insert the air filter into the unit from underside to
upside. See Fig.10.
CAUTION:
DO NOT operate the dehumidifier without a filter
because dirt and lint will clog it and reduce
performance.
4 . When not using the unit for long time periods
After turning off the unit, wait one day before emptying
the bucket.
Clean the main unit, water bucket and air filter.
Cover the unit with a plastic bag.
Store the unit upright in a dry, well-ventilated place.

CARE AND MAINTENANCE

Fig. 8
Fig. 9
Fig. 10