SPARKY BPR 15Li Instrucciones De Uso Originales página 11

operating in areas with insufficient light. To turn
the LED light on press the ON/OFF switch (3).
OPERAtION mODE sElECtION
Select the operation mode by means of the switch (5).
WARNING: Switching between opera-
tion modes shall be performed only if the power
tool is switched off!
"Hammer drilling" mode - hammer
drilling in concrete, stone, masonry, etc.
(Fig.1a)
"Drilling" mode - drilling in metal, wood,
plastics, etc. (Fig.1b)
REvERsING (Fig. 2)
WARNING: Reversing can be per-
formed only when the spindle is not rotating!
The extreme position of the lever (4) to the right is
equivalent to anti-clockwise rotation, the extreme
position to the left - to clockwise rotation.
When the ON/OFF switch (3) is depressed the le-
ver (4) can not be actuated.
Drilling and driving in screws is performed with the
lever (4) in its extreme position to the left. Loos-
ening screws and releasing a jammed drill bit is
performed with the lever (4) in its extreme position
to the right.
PROtECtIvE RING
The prevents penetration of dust generated dur-
ing drilling into the socket for the bit shank. (Fig. 3)
Take care not to damage the protective ring (7)
while inserting the bit.
WARNING: A damaged protective ring
it must be immediately replaced in an author-
ised service centre.
INsERtING sDs-PlUs bIts
Clean and grease the shank of the accessory, be-
fore placing it into the socket!
Pull the locking sleeve (6) backward (6). (Fig. 4)
Insert the bit untill stop. Ensure that the socket
grooves correspond to the shank channels, and
then release the sleeve to fix the bit.
Check the proper tightening of the bit attempting
to pull it near the sleeve.
Original instructions
All manuals and user guides at all-guides.com
To remove the bit, pull the sleeve (6) back, and
then take the bit out.
INsERtING stRAIGHt sHANK bIts
SDS-plus shanks for hammer drilling! Other-
wise the tool and the chuck will be damaged.
mounting the keyless chuck
Clean and grease the SDS-plus shank of the
chuck adapter.
Pull the locking sleeve (6) backward. (Fig. 5)
Insert the adapter shank until stop. Ensure that the
socket grooves correspond to the adapter shank
channels, and then release the sleeve to fix the
chuck with adapter (16).
Check the proper tightening of the adapter at-
tempting to pull it near the sleeve.
To remove the chuck, pull the locking sleeve (6)
backward and take the chuck with adapter out.
Inserting a bit into the keyless chuck
Open the chuck (16) by rotating its front collar in
the direction of the symbol "RELEASE". (Fig. 6)
Insert the bit shank into the chuck.
Grip the rear collar of the chuck and rotate its front
collar in the direction of the symbol "GRIP".
Set the operation mode switch (5) to position for
"Drilling" mode.
To remove the bit, grip the rear chuck collar and
rotate its front collar in the direction of the symbol
"RELEASE".
sWItCHING ON - sWItCHING Off
switching on: Press and hold the ON/OFF
switch (3). (Fig. 7)
switching off: Release the ON/OFF switch (3).
At low temperatures the power tool reaches its en-
tire hammer capacity only after a certain time.
The power tool is equipped with a brake. The spin-
dle stops rotating immediately after releasing the
switch trigger.
smOOtH ElECtRONIC RPm CONtROl
Light pressure on the ON/OFF trigger switch (3)
results in low rotation speed / low impact rate,
further pressing the switch results in smooth in-
crease of the rpm to maximum upon reaching the
extreme position. (Fig. 8)
bAttERy stAtE INDICAtION
▪
WARNING: Do not ise tools without
The LED indicator (9) shows the battery charge
level upon pressing the ON/OFF trigger switch
9
EN