Specifications; Product Specifications; Engine Specifications - Craftsman 580.750401 Instrucciones De Uso

ENGINE TECHNICAL INFORMATION
This is a single cylinder, air cooled Model 090000
engine. The Emission Control System for this
pressure washer is warranted for standards set
by the Environmental Protection Agency and the
California Air Resources Board. Certification does
not grant the purchaser, owner or operator of this
engine any additional warranties with respect to the
performance or operational life of this engine. The
engine is warranted solely according to the product and
emissions warranties stated elsewhere in this manual.
Power Ratings
The gross power rating for individual gasoline engine
models is labeled in accordance with SAE (Society
of Automotive Engineers) code J1940 Small Engine
Power & Torque Rating Procedure, and is rated in
accordance with SAE J1995. Torque values are
derived at 2600 RPM for those engines with "rpm"
called out on the label and 3060 RPM for all others;
horsepower values are derived at 3600 RPM.
The gross power curves can be viewed at www.
BRIGGSandSTRATTON.COM. Net power values are
taken with exhaust and air cleaner installed whereas
gross power values are collected without these
attachments. Actual gross engine power will be higher
than net engine power and is affected by, among other
things, ambient operating conditions and engine-to-
engine variability. Given the wide array of products on
which engines are placed, the gasoline engine may not
develop the rated gross power when used in a given
piece of power equipment. This difference is due to a
variety of factors including, but not limited to, the variety
of engine components (air cleaner, exhaust, charging,
cooling, carburetor, fuel pump, etc.), application
limitations, ambient operating conditions (temperature,
humidity, altitude), and engine-to engine variability.
Due to manufacturing and capacity limitations, Briggs &
Stratton may substitute an engine of higher rated power
for this engine.

SPECIFICATIONS

PRODUCT SPECIFICATIONS

Pressure Washer Specifications
Outlet Pressure . . . . . . . . . . . . . . . . . . . . . . . 2,200 PSI*
Flow Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.9 GPM*
Detergent Mix . . . . . . . . . . . . . . . . . . . . Use as directed
Water Supply Temperature . . . . . Not to exceed 100°F

Engine Specifications

Bore . . . . . . . . . . . . . . . . . . . . . . . . . . 2.495 in. (63.4 mm)
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . 1.75 in. (44.45 mm)
Displacement . . . . . . . . . . . . . . . . . . . . . . 8.64 in. (140 cc)
Spark Plug
Type: . . . . . . . . . . . . . . . . . . Briggs & Stratton 692051
Set Gap To: . . . . . . . . . . . . . . . . . . 0.020 in. (0.50 mm)
Armature Air Gap: . . . . . . 0.006-0.014 in.(0.15-0.36 mm)
Valve clearance with valve springs installed and piston
1/4 in. (6 mm) past top dead center (check when engine
is cold).
Intake . . . . . . . . . . . . . . . . 0.004-0.008 in.(0.10-0.20 mm)
Exhaust . . . . . . . . . . . . . . . 0.004-0.008 in.(0.10-0.20 mm)
Fuel Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8 Quarts
Oil Capacity . . . . . . . . . . . . . . . . . . 15 Ounces (0.44 liter)
NOTICE For practical operation, the engine load
should not exceed 85% of rated power. Engine power
will decrease 3-1/2% for each 1,000 ft. (300 m) above
sea level and 1% for each 10° F (5.6° C) above 77° F
(25° C). It should operate satisfactorily at an angle up
to 15°.
* This pressure washer is rated in accordance to
the Pressure Washer Manufacturers Association
(PWMA) standard PW101-2010 (Testing and Rating
Performance of Pressure Washers).
15