Cleaning Detergent Siphoning Tube - Craftsman 580.752160 Instrucciones De Uso

7. Engage trigger lock on spray gun and start engine
following instructions How to Start Your Pressure
Washer.
8A. If using cleaning tank, rotate detergent shut-off valve on
cleaning tank to "On" position (A).
IMPORTANT: If using detergent siphoning hose, make sure
detergent shut-off valve on cleaning tank is in the "Off"
position.
8B. If using detergent siphoning hose, place small filter end
of detergent siphoning tube into detergent container.
NOTE: Make sure the filter is fully submerged in detergent
while applying detergent.
NOTICE
Contact with the hot muffler can damage detergent
siphoning tube.
• When inserting the filter into a detergent solution bottle, route
the tube so as to keep it from inadvertently contacting the hot
muffler.
9. Apply detergent to a dry surface, starting at lower
portion of area to be washed and work upward, using
long, even, overlapping strokes.
10. Allow detergent to "soak in" for 3-5 minutes before
washing and rinsing. Reapply as needed to prevent
surface from drying. DO NOT allow detergent to dry on
(prevents streaking).
IMPORTANT: When using the detergent siphoning hose, you
must flush the detergent siphoning system after each use by
placing the filter into a bucket of clean water, then run the
pressure washer in low pressure for 1-2 minutes.
Pressure Washer Rinsing
After detergent is applied, scour the surface and rinse it clean
as follows:
1. If using cleaning tank, rotate detergent shut-off valve on
cleaning tank to "Off" position.
2. Rotate PrecisionSpray™ Selector to a high pressure
position, as described in the PrecisionSpray™ Selector
instruction sheet.
3. Keep spray gun a safe distance from spray surface.
• Operate pressure washer from a stable surface.
• Be extremely careful if you must use the pressure washer from
a ladder, scaffolding, or any other similar location.
• Firmly grasp spray gun with both hands when using high
pressure spray to avoid injury when spray gun kicks back.
A
4. Apply a high pressure spray to a small area and then
check the surface for damage. If no damage, proceed to
step 5.
5. Start at top of area to be rinsed, working down with
same overlapping strokes used for cleaning.

Cleaning Detergent Siphoning Tube

If you used the detergent siphoning tube, you must flush it
with clean water before stopping the engine.
1. Engage trigger lock on spray gun.
2. Place detergent siphoning tube/filter in a bucket full of
clean water.
3. Rotate PrecisionSpray™ Selector to a low pressure
position, as described in the PrecisionSpray™ Selector
instruction sheet.
4. Flush for 1-2 minutes.
5. Shut off engine following instructions How to Stop
Pressure Washer and turn off water supply.
6. ALWAYS point gun in a safe direction and squeeze spray
gun trigger to release retained high water pressure.
IMPORTANT: Spray gun traps high water pressure, even when
engine is stopped and water is disconnected.
• Keep high pressure hose connected to pump and spray gun
while system is pressurized.
• ALWAYS point spray gun in safe direction and squeeze spray
gun trigger, to release high pressure, every time you stop
engine. Engage trigger lock when not in use.
Automatic Cool Down System (Thermal Relief)
If you run the engine on your pressure washer for
3-5 minutes without pressing the trigger on the spray gun,
circulating water in the pump can reach temperatures above
125°F. The system engages to cool the pump by discharging
the warm water onto the ground.
13
WARNING
Kickback from spray gun can cause you to fall.
WARNING
The high pressure stream of water that this
equipment produces can cut through skin and its
underlying tissues, leading to serious injury and
possible amputation.
Spray gun traps high water pressure, even when
engine is stopped and water is disconnected,
which can cause injury.