Earthing Instructions - Titan 750e Series Instrucciones De Uso

Safety regulations
HAZARD: EXPLOSION HAZARD DuE TO INCOMPATIBLE
MATERIALS
Will cause severe injury or property damage.
PREVENTION:
• Do not use materials containing bleach or chlorine.
• Do not use halogenated hydrocarbon solvents such as
methylene chloride and 1,1,1 - trichloroethane. They
are not compatible with aluminum and may cause an
explosion. If you are unsure of a material's compatibility
with aluminum, contact your coating's supplier.
HAZARD: GENERAL
This product can cause severe injury or property damage.
PREVENTION:
• Read all instructions and safety precautions before
operating equipment.
• Follow all appropriate local, state, and national codes
governing ventilation, fire prevention, and operation.
• Pulling the trigger causes a recoil force to the hand that is
holding the spray gun. The recoil force of the spray gun is
particularly powerful when the tip has been removed and
a high pressure has been set on the airless pump. When
cleaning without a spray tip, set the pressure control knob
to the lowest pressure.
• Use only manufacturer authorized parts. User assumes all
risks and liabilities when using parts that do not meet the
minimum specifications and safety devices of the pump
manufacturer.
• Before each use, check all hoses for cuts, leaks, abrasion
or bulging of cover. Check for damage or movement of
couplings. Immediately replace the hose if any of these
conditions exist. Never repair a paint hose. Replace it with
another earthed high-pressure hose.
• Make sure power cord, air hose and spray hoses are routed
in such a manner to minimize slip, trip and fall hazard.
• Clean up all material and solvent spills immediately to
prevent slip hazard.
• ALWAYS follow the material manufacturer's instructions
for safe handling of paint and solvents.
• Do not use this unit in workshops that are covered under
the explosion prevention regulations.
• Always unplug cord from outlet before working on
equipment (electric units only).
• Always keep the power cord plug in sight during usage to
prevent any accidental shutdown or startup.
• Wear ear protection. This unit can produce noise levels
above 85 dB(A).
• Device weighs in excess of 18 kg. Two-person lift is
required.
• Never leave this equipment unattended. Keep away from
children or anyone not familiar with the operation of
airless equipment.
• Do not move unit while unit is running.
• Do not spray on windy days.
Performance Series 750e
GB
HAZARD: HAZARDOuS VAPORS
Paints, solvents, insecticides, and other materials can be
harmful if inhaled or come in contact with body. Vapors
can cause severe nausea, fainting, or poisoning.
PREVENTION:
• Use a respirator or mask if vapors can be inhaled. Read
all instructions supplied with the mask to be sure it will
provide the necessary protection.
• Wear protective eyewear.
• Wear protective clothing as required by coating
manufacturer.
1.1

Earthing Instructions

Electric models must be earthed. In the event of an electrical
PE short circuit, earthing reduces the risk of electric shock by
providing an escape wire for the electric current. This product
is equipped with a cord having an earthing wire with an
appropriate earthing plug. The plug must be plugged into an
outlet that is properly installed and earthed in accordance with
all local codes and ordinances.
DANGER — Improper installation of the earthing plug can
result in a risk of electric shock. If repair or replacement of
the cord or plug is necessary, do not connect the green
earthing wire to either blade terminal. The wire with
insulation having a green outer surface with or without
yellow stripes is the earthing wire and must be connected
to the earthing pin.
Check with a qualified electrician or serviceman if the earthing instructions are
not completely understood, or if you are in doubt as to whether the product is
properly earthed. Do not modify the plug provided. If the plug will not fit the
outlet, have the proper outlet installed by a qualified electrician.
Caution – The power cord for this equipment acts as an
emergency stop/emergency switching off device. The
power cord must be placed near an easily accessible,
unobstructed socket-outlet.
Work or repairs at the electrical equipment:
These may only be carried out by a skilled electrician. No liability is assumed
for incorrect installation.
A list of the materials used in the construction of the equipment will be made
available on request to validate compatibility with the coating materials to be
used.
Operating Temperature
This equipment will operate correctly in its intended ambient, at a minimum
between +10°C and +40°C.
Relative Humidity
The equipment will operate correctly within an environment at 50% RH,
+40°C. Higher RH may be allowed at lower temperatures.
Measures shall be taken by the Purchaser to avoid the harmful effects of
occasional condensation.
Altitude
This equipment will operate correctly up to 2000 m above mean sea level.
Transportation and Storage
This equipment will withstand, or has been protected against, transportation
and storage temperatures of -25°C to +55°C and for short periods up to +70°C.
It has been packaged to prevent damage from the effects of normal humidity,
vibration and shock.
5
General view of application