P Roduct Description; Intended Use; Scope Of Supply - df models MegaSpeed XXL 3401 Manual De Instrucciones

3. P
roduct descrIPtIoN
The model is an all-wheel drive RC car chassis with a pre-installed brushless electric motor and a 2.4 GHz receiver station, a
programmed, electronic speed controller, steering servo with metal transmission and two 2S LiPo rechargeable batteries.
The ready-printed and ready-cut-out body as well as the rear spoiler with a carbon look make for a spectacular look, right out
of the box. This model is intended both for operation on indoor tracks as well as operation outdoors.
The double-deck chassis made of anodised aluminium is light and torsion-resistant. Plastic covers screwed onto the chassis
provide the built-in components protection against splashed water and pebbles thrown up.
The two 2S LiPo rechargeable batteries enable symmetrical weight distribution by the longitudinal axis and ensure immense
power output. A low-maintenance brushless motor provides satisfaction with higher power, greater torque and a higher
efficiency factor than conventional brushed motors. A heat sink with a fan attached ensures heat dissipation even under the
most severe conditions.
The unit is powered by the motor pinion on the centre differential. From there one drive shaft each made of metal meshes in
the encapsulated differentials of the front and rear axles, thus bringing about four-wheel drive. The differentials in the front
and rear axles provide for speed compensation between the wheel on the inside and the wheel on the outside of curves and
has metal gears. The model is entyrely ball-bearing-mounted.
A programmable electronic speed controller KL-80 with a fan attached is geared in optimum fashion to the brushless motor
and provides satisfaction through excellent starting behaviour, acceleration and excellent synchronisation.
The high-performance RS 90 MGBB steering servo with metal gearbox has high controlling torque amounting to 9,0 kgcm
(88,3 Ncm) and high control speed with maximum stability. A servo saver also provides protection for the servo against sharp
impacts against the wheels.
Anti-roll bars on front and rear axle each connect the bottom suspension arms of one axle in such a way, that the respective
other wheel is deflected along with a deflected wheel. The roll behaviour in curves of the vehicle is thus curbed and drivea-
bility improved.
In this 2.4 GHz remote control set with two proportional channels and one adjustable switch channel, you own a radio remote
control system that is ideally suited primarily for model cars and model ships. Its proportional control channels allow 2 control
functions to be remotely controlled independently of one another.
Each time the unit is switched on, the link between the transmitter and the receiver is made automatically by AFHDS
(Automatic Frequency Hopping Digital System).

.1 Intended use

This product has been designed solely for private use in the field of modelling and has operating times appropriate to this use.
This product is not approved either for commercial or industrial nor for continuous operation. Any improper use can result
in endangerment to people as well as damage to the product and dangers involved in such, like the loss of control over the
model, short-circuits, fires, electric shock, etc. Comply with the safety instructions in these Operating Instructions. They contain
important information on how to handle this product.
The product is suitable for children under 14 years only under adult supervision.

. Scope of supply

> A 4WD electric RC Buggy with:
• Twin-deck chassis made of anodised aluminium
• 4 rims with multi-spike wheels
• 4 infinitely variable aluminium oil-pressure shock absorbers.
• Buggy body and rear spoiler with carbon look,
cut-out and printed
• 2.4 GHz receiver, pre-installed and pre-adjusted
• Brushless electric motor with heat sink and fan,
pre-installed
• Programmable, KL-80 electronic speed controller with fan,
pre-installed
•
RS 90 MGBB steering servo, pre-installed
> 2.4 GHz 3-channel remote-control transmitter
> Communication plug
> USB cable for connecting the transmitter to the PC,
for controlling simulation programs
> Operating Instructions for the model, the remote control unit
and the speed controller
-  -
3401/V1/0211