Briggs & Stratton 120000 Intek 825 Serie Manual Del Operario página 9

How To Service The Air Filter - Figure 13
WARNING
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Never start or run the engine with the air cleaner assembly or the air filter removed.
•
CAUTION: Do not use pressurized air or solvents to clean the filter. Pressurized air can
damage the filter and solvents will dissolve the filter.
1. Remove the fasteners (A) and the air filter cover (B). (Figure 13).
2. Remove the pre-cleaner (C) and the filter (D).
3. To loosen debris, gently tap the filter on a hard surface. If the filter is excessively
dirty, replace with a new filter.
4. Wash the pre-cleaner in liquid detergent and water. Then allow it to thoroughly air
dry. Do not oil the pre-cleaner.
5. Assemble the dry pre-cleaner to the filter.
6. Install the filter and pre-cleaner into the base (E). Make sure filter fits securely in the
base.
7. Install air filter cover and secure with fasteners. Make sure the fasteners are tight.
How To Replace The Fuel Filter - Figure 14
WARNING
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
Keep gasoline away from sparks, open flames, pilot lights, heat, and other ignition
•
sources.
Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if
•
necessary.
Before replacing the fuel filter, drain the fuel tank or close the fuel shut-off valve.
•
Replacement parts must be the same and installed in the same position as the
•
original parts.
If fuel spills, wait until it evaporates before starting engine.
•
1. Before replacing the fuel filter (A, Figure 14), if equipped, drain the fuel tank or close
the fuel shut-off valve. Otherwise, fuel can leak out and cause a fire or explosion.
2. Use pliers to squeeze tabs (B) on the clamps (C), then slide the clamps away from
the fuel filter. Twist and pull the fuel lines (D) off of the fuel filter.
3. Check the fuel lines for cracks or leaks. Replace if necessary.
4. Replace the fuel filter with an original equipment replacement filter.
5. Secure the fuel lines with the clamps as shown.
How To Clean The Air Cooling System - Figure 15
WARNING
Running engines produce heat. Engine parts, especially muffler, become
extremely hot.
Severe thermal burns can occur on contact.
Combustible debris, such as leaves, grass, brush, etc. can catch fire.
Allow muffler, engine cylinder and fins to cool before touching.
•
Remove accumulated debris from muffler area and cylinder area.
•
CAUTION: Do not use water to clean the engine. Water could contaminate the fuel
system. Use a brush or dry cloth to clean the engine.
This is an air cooled engine. Dirt or debris can restrict air flow and cause the engine to
overheat, resulting in poor performance and reduced engine life.
Use a brush or dry cloth to remove debris from the finger guard (A). Keep linkage,
springs and controls (B) clean. Keep area around and behind the muffler (C) free of any
combustible debris (Figure 15).
en
Storage
WARNING
Gasoline and its vapors are extremely flammable and explosive.
Fire or explosion can cause severe burns or death.
When Storing Gasoline Or Equipment With Fuel In Tank
Store away from furnaces, stoves, water heaters or other appliances that have pilot
•
lights or other ignition sources because they can ignite gasoline vapors.
Fuel System
Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum
deposits to form in the fuel system or on essential carburetor parts. To keep fuel fresh,
use Briggs & Stratton FRESH START
drip concentrate cartridge.
There is no need to drain gasoline from the engine if a fuel stabilizer is added according
to instructions. Run the engine for 2 minutes to circulate the stabilizer throughout the fuel
system. The engine and fuel can then be stored up to 24 months.
If gasoline in the engine has not been treated with a fuel stabilizer, it must be drained into
an approved container. Run the engine until it stops from lack of fuel. The use of a fuel
stabilizer in the storage container is recommended to maintain freshness.
Engine Oil
While the engine is still warm, change the engine oil.
Troubleshooting
Need Assistance? Go to BRIGGSandSTRATTON.COM or call 1-800-233-3723.
Specifications
Engine Specifications
Model
Displacement
Bore
Stroke
Oil Capacity
Tune-up Specifications *
Model
Spark Plug Gap
Spark Plug Torque
Armature Air Gap
Intake Valve Clearance
Exhaust Valve Clearance
* Engine power will decrease 3.5% for each 1,000 feet (300 meters) above sea level and
1% for each 10° F (5.6° C) above 77° F (25° C). The engine will operate satisfactorily at
an angle up to 15°. Refer to the equipment operator's manual for safe allowable
operating limits on slopes.
Common Service Parts n
Service Part
Air Filter, Oval
Air Filter Pre-cleaner, Oval
Oil -- SAE 30
Oil Filter
Fuel Additive
Resistor Spark Plug
Spark Plug Wrench
Spark Tester
Fuel Filter
n We recommend that you see any Briggs & Stratton Authorized Dealer for all
maintenance and service of the engine and engine parts. Use only genuine Briggs &
Stratton parts.
®
fuel stabilizer, available as a liquid additive or a
120000
11.58 ci (190 cc)
2.688 in (68.28 mm)
2.040 in (51.82 mm)
18 -- 20 oz (0.54 -- 0.59 L)
120000
0.020 in (0.51 mm)
180 lb-in (20 Nm)
0.010 - 0.014 in (0.25 - 0.36 mm)
0.004 - 0.008 in (0.10 - 0.20 mm)
0.004 - 0.008 in (0.10 - 0.20 mm)
Part Number
697029, 5059
273356
100005
692513
5041, 5058
692051
89838, 5023
19368
298090, 5018
9