Memory Function - Woods MRD20 Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 49
PLACEMENT OF DEHUMIDIFIER
- The dehumidifier should not be placed
near radiators or other heat sources or
exposed to direct sunlight, as it will reduce
performance.
- Ideal is to put it in the centre
of the room / area.
NOTE: When placed in a shower
room or bathing area, the dehumidifier
should be fixed in place. It is compulsory
to check and respect your local
bathroom electrical regulations before
use.
USING THE DEHUMIDIFIER
If the dehumidifier is transported
horizontally, let the dehumidifier stand
for a 4 hours before being used. It is very
important that the oil runs back into the
compressor, otherwise the dehumidifier
may be seriously damaged.
1. Check that the water reservoir is correctly
placed.
2. Connect the dehumidifier to an grounded
power source.
3. Set the desired humidity level by means of
the humidity control. See the section on the
humidity control.
NOTE: The ambient relative humidity
can be simply measured with the
dehumidifier.
OPERATION MANUAL
1.
Power Button: This button can control
the machine on and off.
2.
Humidity button: To set the desired
humidity.
press Humidity button for
5s, it shows ambient temperature
(0~40°C) for 5s; if you press and
hold the Humidity button, it shows
ambient temperature all the time. If
you don´t press again it automatically
show the NTC sensor temperature
for 5 seconds then, shows ambient
humidity.
3.
Humidity Settings: Open the air outlet
set humidity between 40%, 50%, 60%
or continuous mode.
4.
Timer: When the appliance is on, press
the Timer 2H/4H/6H to operate a
countdown.
5.
during operation, it shows ambient
humidity from 30,31,32···79,80. If it is
<. 30%RH, it shows LO; if it is >80%RH,
6.
Dehumidification mode you can set
humidity level and fan speed 2 levels

MEMORY FUNCTION

1.
Press on/off button (plugged inot
power socket) and then press on/
off button again, it works following
previous setting, but timer and child
lock function has no memory.
2.
No power when operation equals to
plug off all of a sudden the machine
works automatically when there is
power and it memories previous
setting, but child lock function has no
memory.
3.
Unit will automatically turn on and
operates in last setting after power
returns.. It works under initial default
setting during dehumidification mode
and works under humidity setting by
50%RH on high speed.
COMPRESSOR PROTECTION FUNCTION
The unit is equipped with compressor
protection function—that is, compressor
has five minutes period between starts
operation and shut down.
WATER DRAINAGE
When the water reservoir is full, the
dehumidifier is shut off automatically.
Once the water reservoir is emptied the
unit will automatically restart.
1.
Disconnect the dehumidifier from the
power source.
2.
Empty the water reservoir.
3.
Put the empty water reservoir back
and check that the float moves freely.
4.
Connect the dehumidifier to the
power source.
Direct water drainage
Connect a water hose to the pipe on the
back of the dehumidifier. Lead the other
end to a drain. Make sure that the water
can be drained downwards.
AIR FILTER
The air filter prevents dust and dirt from
entering the machine, prolonging its life
expectancy. It
is important the filter is cleaned regularly.
Operating Instructions
Filter cleaning:
1.
Remove the filter.
2.
Wash it with warm water and a mild
cleansing agent. Alternatively the
filter may be vacuum cleaned.
3.
Let the filter dry and put it back.
DEFROSTING OPERATION
During the defrosting operation, the
dehumidification function may intermit.
Please don't turn off the switch or pull out the
power plug of the dehumidifier during the
defrosting operation. This dehumidifier can't be
applicable to keep extreme low temperature.
The purpose of this dehumidifier is to pump off
the unpleasant high humidity in daily life and
dry the wet things. But it can't be used to keep
extreme low temperature.
The room temperature increases during the
operation.
This dehumidifier doesn't have colling function.
It will produce heat during the operation and
increase the room temperature to 1 to 4°C. In
addition, the door and windows are closed and
other appliances in the room can give out heat
as well as the radiation of the sun can raise the
room temperature.
GB
11

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mrd25

Tabla de contenido