Technical Data - Titan LP Serie Manual Del Operador

EN
English (English)

1. TECHNICAL DATA

Model
Sound pressure dB(A), K
L
pA
Declaration of noise and vibration statement
Guaranteed sound power level Lw according to EN ISO 3744 in accordance with directive 2000/14/EC. Sound pressure level Lp according to EN ISO 11201, EN
500-4:2011.These declared values were obtained by laboratory type testing in accordance with the stated directive or standards and are suitable for comparison
with the declared values of other machines tested in accordance with the same directive or standards. These declared values are not suitable for use in risk
assessments and values measured in individual work places may be higher. The actual exposure values and risk of harm experienced by an individual user are
unique and depend upon the way the user works, in what material the machine is used, as well as upon the exposure time and the physical condition of the user,
and the condition of the machine. We, Chicago Pneumatic Tool Company LLC, cannot be held liable for the consequences of using the declared values, instead
of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control.
2. MACHINE TYPE(S)
• This product is designed for installing and removing threaded fasteners. For use only with Titan hydraulic power packs.
• No other use permitted. For professional use only.
• Use with Titan hoses and accessories.
3. GENERAL INFORMATION
Inspection
• Prior to use, inspect tool for any damage caused in the shipping process, if there is damage, contact your Titan sales representative immediately.
• All Titan Products are supplied assembled and ready for immediate use. The use of Titan Power Pack is strongly recommended to provide the proper flow,
speed and accuracy of your hydraulic tools.
• The accuracy of your new Titan Hydraulic Torque Tools is ±3%. Titan Hydraulic tools may be calibrated by Titan or by any calibration facility that can be traced
to the National Institute of Standards and Technology (N.I.S.T).
Hydraulics, Connections, and Safety Precautions
• All Titan Hydraulic Torque Tools operate at 700 bar (10 000psi).
• Make sure all hoses are rated for 700 bar (10 000 psi)
• Before connecting or disconnecting hydraulic hoses release any pressure by turning the pump off and double checking that the pressure gauge reads Zero
(0). When connecting hose to the pump or tool, check fitting for cleanliness and ensure the fitting is engaged fully and hand tight.
WARNING:
• Always ensure both hoses are securely connected.
• Do not attempt to force the fitting using a wrench or any other means!
Electric Power Requirements and Safety Precautions
• Check the specification plate located on the pump for proper power requirements. Operating the pump with the wrong power source will cause motor failure. If
you are unsure of the power requirements in your facility, seek a qualified electrician for guidance.
WARNING:
• Do not remove the grounding prong from the electrical plug.
• Electrical motors should not be used in volatile situations. Do not use an electrical pump in explosive atmospheres or in the presence of conduc-
tive liquids. In these situations a Titan Air Pump should be used.
Air Connections
• Please consult your compressor manufacturer's air flow rating prior to using and pressurizing your pump.
• Improper airflow will damage the pump motor. Titan recommends an air‐hose with a diameter greater than 3/4".
• A filter lubricator regulator unit (FLR) should be used. An FLR will regulate flow and pressure as well as lubricate and remove water from compressed air to
keep the air motor in your pump running properly.
FLR Unit - Connections
• Consult your compressor manufacturer's air flow rating prior to using and pressurizing your pump.
• Airflow will damage the pump motor. Titan recommends an air‐hose with a diameter greater than lubricator regulator unit (FLR) should be used. An FLR will
regulate flow and pressure as well as lubricate water from compressed air to keep the air motor in your pump running properly.
4. TOOL OPERATION
Connecting the System
• All hydraulic connections are rated for 700 Bar (10 000 psi). Connect the couplers on the hose, tool, and pump as shown in Figure 2.
• Make sure male couplers are connected to female couplers and are fully engaged and hand tight.
Warning:
• Tightening fittings with a tool may cause permanent thread damage and will lead to failure of the fitting.
• ALWAYS CONNECT BOTH HOSES!!!!
• Failure to connect the retract fitting may result in tool failure, serious injury, or death.
• To avoid tool malfunction do not reverse the connector on either the pump or the tool.
Assembling Cylinder and Link
1. Align Cylinder and Link as shown in Figure 4.
2. Rotate cylinder till flush with link as shown in Figure 5.
3. Insert mating pin till flush with the link as shown in Figure 6.
Hex
Torque max
Dimension
1 2
[Nm]
[inch]
[mm]
[Ft.lb]
= K = 3 dB Uncertainty. EN ISO 15744
pA WA
Weight
Torque min
Cylinder
3
[Nm] [kg]
[lb]
[Ft.lb]
HYDRAULIC WRENCH
Sound pressure
Link L
pA
4
[dB(A)]
LP series
Soundpower
L
wA
6
[dB(A)]