Bosch PMF 350 CES Manual Original página 16

16 | English
sanding dust is mixed with paint or polyurethane residue
or with other chemical substances and if the workpiece is
hot as a result of prolonged work.
Keep hands away from the sawing area. Do not reach
u
under the workpiece. Contact with the saw blade can
lead to injuries.
Clean the air vents on your power tool regularly. The
u
motor's fan will draw the dust inside the housing and ex-
cessive accumulation of powdered metal may cause elec-
trical hazards.
Use suitable detectors to determine if utility lines are
u
hidden in the work area or call the local utility com-
pany for assistance. Contact with electric lines can lead
to fire and electric shock. Damaging a gas line can lead to
explosion. Penetrating a water line causes property dam-
age or may cause an electric shock.
Hold the power tool firmly with both hands and make
u
sure you have a stable footing. The power tool can be
more securely guided with both hands.
When changing the application tool, wear protective
u
gloves.Application tools can become hot when used for
prolonged periods of time.
Do not scrape any dampened materials (e.g. wallpa-
u
per) or on damp surfaces. Water entering a power tool
increases the risk of electric shock.
Do not treat the surface you will be working on with
u
any fluids that contain solvents. Poisonous vapours
may develop due to the materials heating up when being
scraped.
Take particular care when handling scrapers and
u
blades. The application tools are very sharp. Danger of in-
jury.
Products sold in GB only:
Your product is fitted with an BS 1363/A approved electric
plug with internal fuse (ASTA approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an au-
thorised customer service agent. The replacement plug
should have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains
socket elsewhere.
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended Use
The power tool is intended for sawing and cutting wood-
based materials, plastic, plasterboard, non-ferrous metals
1 609 92A 4K3 | (12.10.2018)
and mounting elements (e.g. nails, clamps). It is also suit-
able for working on soft wall tiles and for dry sanding and
scraping of small areas. It is ideal for working close to edges
and flush with surfaces.
Product Features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) AutoClic lever for unlocking the application tool/ac-
cessory
(2) On/off switch
(3) Ventilation slots
(4) Orbital stroke rate preselection thumbwheel
(5) Thread for auxiliary handle
(6) Auxiliary handle (insulated gripping surface)
(7) 180° light band
(8) Tool holder
A)
(9) Plunge cut saw blade
A)
(10) Sanding plate
A)
(11) Sanding sheet
A)
(12) Depth stop
A)
(13) Segment saw blade
(14) Handle (insulated gripping surface)
A)
(15) Dust extraction hose
A)
(16) Dust extraction outlet
A)
(17) Dust extraction system
(18) Clamping lever for dust extraction system
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical Data
Multifunction tool
Article number
Orbital stroke rate preselec-
tion
Constant electronic control
Soft start
AutoClic tool holder
Rated power input
Power output
No-load speed n
0
Oscillation angle on left/
right
Weight according to
EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
A)
PMF 350 CES
3 603 A02 2..
●
●
●
●
W 350
W 185
−1
min 15000–20000
° 1.4
kg 1.6
/ II
Bosch Power Tools