Bosch PMF 350 CES Manual Original página 20

20 | English
Insert the appropriate segment saw blade for the desired
cutting depth. Slide the depth stop (12) from the tool holder
(8) in the direction of the application tool until you can ro-
tate it freely. Rotate the depth stop (12) so that the desired
cutting depth is above the section of the saw blade that will
be used to saw. Slide the depth stop (12) onto the collar of
the power tool once again as far as it will go.
Remove the depth stop (12) for all other cutting depths and
for working with other application tools. To do this, remove
the application tool and pull the depth stop away from the
collar.
Choosing the Sanding Sheet
Different sanding sheets are available, depending on the material you are working with and the required surface removal rate:
Sanding sheet Material
– All wood and wood-
based materials (e.g.
hardwood, softwood,
chipboard, construction
Red quality
boards)
– Metal materials
– Paint
– Varnish
– Filler
– Bodyfiller
White quality
Attaching/changing the sanding sheet on the sanding
plate
The sanding plate (10) is fitted with a hook-and-loop fasten-
ing, allowing sanding sheets with a hook-and-loop backing to
be secured quickly and easily.
Tap the hook-and-loop fastening of the sanding plate (10)
before fitting the sanding sheet (11) to facilitate maximum
adhesion.
Position the sanding sheet (11) so that it is flush with one
side of the sanding plate (10), then place the sanding sheet
on the sanding plate and press it on firmly.
To ensure optimum dust extraction, make sure that the
punched holes in the sanding sheet are aligned with the
drilled holes in the sanding plate.
To remove the sanding sheet (11), take hold of it by a corner
and pull it away from the sanding plate (10).
You can use all sanding sheets, polishing and cleaning
fleeces from the Delta 93 mm series in Bosch's range of ac-
cessories.
Sanding accessories such as fleece/polishing felt are at-
tached to the sanding plate in the same way.
1 609 92A 4K3 | (12.10.2018)
Fitting the Auxiliary Handle (accessory)
The low-vibration auxiliary handle enables the tool to be
used safely and more comfortably.
Screw the auxiliary handle into the thread (5) on the left or
right of the machine head depending on how you are work-
ing.
Do not continue to use the power tool if the auxiliary
u
handle is damaged. Do not make any alterations to the
auxiliary handle.
Application
For pre-sanding, e.g. of rough and uneven beams and
boards
For surface sanding and levelling of slight irregularities Medium
For finish-sanding and fine sanding of wood
For sanding down paint
For sanding undercoats (e.g. removing brushstrokes,
paint drips and paint runs)
For final sanding of primers prior to painting
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Connecting the dust extraction system (see figure C)
The dust extraction system (17) is only designed for use
with the sanding plate (10); it serves no purpose when used
together with other application tools.
Grit
Coarse 40
60
80
100
120
Fine 180
240
320
400
Coarse 40
60
Medium 80
100
120
Fine 180
240
320
Bosch Power Tools