Publicidad

Enlaces rápidos

front runner
START HERE!
Don't be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
FAJL002 / FAJL003_REV_A01
jeep wrangler jl (2018 - current)
inner brackets and Foot Rail
READ ME FIRST
IMPORTANT WARNING!
Please call us if you have any questions about the installation of this product.
1
FAJL002 / FAJL003
© 2019 FRONT RUNNER VEHICLE OUTFITTERS
ENG

Publicidad

Tabla de contenido
loading

Resumen de contenidos para Front Runner FAJL002

  • Página 1 Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain aspects of your warranty. Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components. A complete kit will contain: 1.
  • Página 2 M8 x 16 x 1.6SS Flat Washer 13MM 13MM 14 X M8 Nyloc Nut 14 X M8 Nut Cap - Vacuum Cleaner Allen Key - a Friend 22mm (7/8") Hole Saw FIGURE 1.2 FAJL002 / FAJL003_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 3 Aluminum Spacer M6 x 12 x 1SS Flat Washer M6 Nyloc Nut M8 x 16 x 1.6SS Flat Washer M8 SS Spring Washer M8 x 25 Button Head Bolt FIGURE 1.1 FAJL002 / FAJL003_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 4 Bolts, M8 SS Spring Washers and M8 x 16 x 1.6 SS Flat Washers (Items 16, 17 & 20). Refer to Figure 1.1 on page 3. 13mm Do this on both left and right side. FAJL002 / FAJL003_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 5 After drilling, clean the area around all the 22mm holes in the roof with a rag and methylated spirits/denatured alcohol. Refit both LH and RH Inner Support Bracket. Refer to Step 2.2. 13mm FAJL002 / FAJL003_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 6 M6 Nyloc Nuts (Items 9, 10, 11, 14 & 15) as shown. Do this on both sides of the vehicle. 10mm Finish off by placing M6 Nut Caps (Item 8) on all the nyloc nuts and bolt heads. 13mm 13mm FAJL002 / FAJL003_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 7 Leave the Foam Washer and the Aluminum Spacers in place. Screw in the Sealing Plugs, reusing the M6 Nyloc Nuts and Washers that held the Foot Rail in 13mm position. FAJL002 / FAJL003_REV_A01 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 8 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
  • Página 9: Important Warning

    TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
  • Página 10 M8 x 16 Hex Head Bolt Pillar Bracket 1LH+1RH RH Front Support Arm M6 x 50 Button Head Screw M6 Spring Washer M6 Flat Washer M6 Large Washer M8 x 20 Hex Head Bolt FIGURE 1.1 FAJL004_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 11 Washers (Items 5, 6 & 2). 13mm Make sure the Support Arms are straight, using the door shut line as a guide. fully tighten the M8 Button Heads and then the M6 Button Heads on top. FAJL004_REV_A01 © 2020 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 12 PREP FOR RACK INSTALL (FULL RACK) Before moving to the next step you need to install the Inner and Middle Support Brackets. Refer to FAJL002 & FAJL003 Fitment Guides. If not already assembled, assemble your Tray as per the Universal Tray Assembly Instructions.
  • Página 13 IMPORTANT! FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
  • Página 14 FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL. NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
  • Página 15 M8 x45 Button Head Bolt Thick Joiner Piece Thin Joiner Piece Side Profile Corner Combined Slat 28 X M8 x 25 Button Head Bolt 12 X Standard Slat M6 x 10 Button Head Bolt FIGURE 1.1 RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 16 Slide the matching Side Profile over the two Joiner pieces, remembering to insert a Nyloc Nut, and fasten once again using a M8 x 45 Button Head Bolt. Repeat the above steps for the other side. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 17 Combined Slat and Standard Slats, aligning the holes and loosely inserting the M8 x 25 Button Heads as you work your way to the Combined Slat at the other end. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 18 Push the Corner into position as shown, aligning the hole in the Corner with the Rivnut already inserted in the Combined Slat. Use a M6 x 12 Button Head Bolt (Item 10) and fasten the Corner in position. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 19 RACK ASSEMBLY - WIND DEFLECTOR IN THE BOX TOOLS NEEDED Slimline II Tray M8 Half Nut Wind Deflector (1LH + 1RH) Schnorr Washer M8 x 12 Button Head Bolt FIGURE 1.2 RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 20 Slide them to the center of the Combined Slat making sure that the Schnorr Washer is above the T-slot Channel. Assemble Items 2, 4 & 5 to both LH & RH Wind Deflectors (Item 3) as shown. RRSTUNI_REV_A05 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 21 Wind Deflectors slightly apart, leaving a gap of about 20 - 30mm. USEFULL TIP - PRE-LOAD TIE DOWN RINGS It is usefull to fit Tie-Down Rings (RRAC012) to your Front Runner Rack for future use before you fit any accessories. Insert the Tie Down Rings into the machined slots and position them in the center of the rack.
  • Página 22 It's easy! Take care of your Front Runner gear the same way you do the exterior of your vehicle: Rinse with clean water and wipe down with a soft dry cloth. For stubborn spots, use a soft brush and mild soap.
  • Página 23 BEFESTIGUNGEN VOR EINER VERWENDUNG REGELMÄßIG AUF EINSTELLUNG, ABNUTZUNG ODER SCHÄDEN ZU PRÜFEN. LIES DAHER UNBEDINGT VOR DER MONTAGE ODER DER VERWENDUNG ALLE MIT DEINEM FRONT RUNNER PRODUKT GELIEFERTEN ANWEISUNGEN UND HINWEISE. FALLS DU NICHT ALLE ANWEISUNGEN ODER HINWEISE VERSTEHST ODER DU KEINE TECHNISCHE ERFAHRUNG BESITZT UND MIT DEM ZUSAMENBAUEN NICHT VERTRAUT BIST, SOLLTEST DU DAS PRODUKT VON TECHNISCHEM FACHPERSONAL ODER EINER ANDERWEITIG QUALIFIZIERTEN PERSON VERBAUEN LASSEN.
  • Página 24 32 X M8 Selbstsichernde Mutter M8 x 45 Rundkopfschraube Dickes Verbindungsstück 4 MM 5 MM Dünnes Verbindungsstück Seitenprofil Eckstück Kombileiste 28 X M8 x 25 Rundkopfschraube 12 X Querleiste M6 x 10 Rundkopfschraube ABBILDUNG 1.1 RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 25 Schiebe das zugehörige Seitenprofil über die zwei Verbindungsstücke und denk daran, eine selbstsichernde Mutter einzusetzen. Befestige auch diese Verbindung mit einer m8 x 45 Rundkopfschraube. Wiederhole die oben beschriebenen Schritte für die andere Seite. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 26 5 MM Kombileiste sein. Verwende eine M8 x 25 Rundkopfschraube (Teil 8) und ziehe sie mit einem 5 mm-Innensechskantschlüssel fest. Die Plattform bleibt mit der Unterseite nach oben gedreht, für die Montage der 7 Querleisten. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 27 Schau Dir nochmal Schritt 3.1 an - Schiebe danach die zweite Kombileiste in die zwei Seitenprofile und befestige sie, wie in Schritt 3.2 beschrieben. FESTZIEHEN ALLER SCHRAUBEN Ziehe mit Deinem 5 mm-Innensechskantschlüssel alle Rundkopfschrauben fest. Das empfohlene Drehmoment für die M8 Rundkopfschrauben ist 20 Nm oder 15 ftlb. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 28 Vergewissere Dich in der jeweiligen Montageanleitung, ob das der Fall ist. MONTAGE DES WINDABWEISERS INHALT DU BENÖTIGST Slimline II Dachträger M8 Halbmutter Windabweiser (1L + 1R) 5 MM Unterlegscheibe M8 x 12 Rundkopfschraube ABBILDUNG 1.2 RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 29 (Teil 2, 4 & 5) wie dargestellt in die Kombileiste. Schiebe sie bis zur Mitte der Kombileiste, wobei Du sicherstellen musst, dass die Unterlegscheibe über der T-Nut sitzt. Montiere Teil 2, 4 & 5 wie abgebildet an beiden Windabweisern. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 30 (RRAC012) am Dachträger vor der Montage von zusätzlicher Ausrüstung bereits vorhanden sind. Einfach die Ringschrauben in die T-Nut auf den Leisten in der Mitte befestigen und somit vorbereitet sein, falls weitere Accessoires und Ausrüstung montiert werden soll. RRSTUNI_REV_A04 © 2019 FRONT RUNNER OUTFITTERS...
  • Página 31 Im salzigen Küstenklima oder verschneiten Regionen, in denen Streusalz auf den Straßen genutzt wird, verwende auf Silikonbasis beschaffenes Öl oder Spray, um die Muttern und Schrauben dauerhaft vor Korrosion zu schützen. HOL DIR NOCH MEHR AUSRÜSTUNG VON FRONT RUNNER Besuche uns Online auf www.FrontRunnerOutfitters.com Markiere uns immer und überall! #FrontRunnerOutfitters #BornToRoam...
  • Página 32: Advertencia Importante

    LOS PRODUCTOS PARA SU AJUSTE, DESGASTE Y DAÑOS. POR LO TANTO, DEBE LEER Y COMPRENDER TODAS LAS INSTRUCCIONES Y PRECAUCIONES SUMINISTRADAS CON SU PRODUCTO FRONT RUNNER ANTES DE LA INSTALACIÓN O EL USO. SI USTED NO ENTIENDE TODAS LAS INSTRUCCIONES Y PRECAUCIONES, O SI NO TIENE EXPERIENCIA MECÁNICA Y NO ESTÁ...
  • Página 33: Herramientas Necesarias

    Pieza de ensamble gruesa Pieza de ensamble delgada Perfil lateral Esquina Barra combinada 28 X M8 x 25 Tornillo cabeza de botón 12 X Barra estándar M6 x 10 Tornillo cabeza de botón FIGURA 1.1 RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 34: Montaje De Baca - Perfiles Laterales

    Deslice el perfil lateral coincidente sobre las dos piezas de ensamble, recordando insertar una tuerca nyloc, y apriete una vez más usando un tornillo cabeza de botón M8 x 45. Repite los pasos anteriores para el otro lado. RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 35: Montaje De Baca - Barras Combinadas

    El orificio final del perfil lateral debe alinearse con el orificio en la barra combinada. Utilice un cabeza de botón M8 x 25 (artículo 8) y apriete ligeramente con una llave Allen de 5mm. RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 36: Montaje De Baca - Barras Estándar

    Con su llave Allen de 5mm, apriete todos los tornillos cabeza de botón. El ajuste de par recomendado para los tornillos cabeza de botón M8 es de 20 Nm o 15 ft lb. © 2019 FRONT RUNNER VEHICLE OUTFITTERS RRSTUNI_REV_A04...
  • Página 37: Montaje De Baca - Deflector De Viento

    Schnorr está por encima del canal ranura en T. Ensamble los elementos 2, 4 y 5 a ambos deflectores de viento LH & RH (artículo 3) como se muestra. RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 38: Montaje De Baca -Esquinas

    MONTAJE DE BACA - DEFLECTOR DE VIENTO EN LA CAJA HERRAMIENTAS NECESARIAS Baca portaequipaje Slimline II M8 Tornillo medio Deflector de viento (1LH + 1RH) Arandela de seguridad Schnorr M8 x 12 Tornillo cabeza de botón FIGURA 1.2 RRSTUNI_REV_A04 © 2019 FRONT RUNNER VEHICLE OUTFITTERS...
  • Página 39: Inserte La Tuerca Montada En El Deflector

    CONSEJO ÚTIL - ANILLOS DE AMARRE DE PRECARGA Es de mucha utilidad el colocar los anillos de amarre (RRAC012) en la baca portaequipajes de Front Runner para su uso futuro antes de colocar cualquier accesorio. Inserte los anillos de amarre por medio de las ranuras y colóquelos en el centro de...
  • Página 40: Consulte La Guía De Instalación De Su Vehículo

    ¡Es fácil! Cuida tu equipo Front Runner de la misma manera que haces con el exterior de tu vehículo: Enjuague con agua limpia y limpie con un paño suave y seco. Para manchas persistentes, usa un cepillo suave y un jabón suave.

Este manual también es adecuado para:

Fajl003

Tabla de contenido