General Safety Rules - Bosch Wallscanner D-tect 150 Instrucciones De Funcionamiento Y Seguridad

Dtect150_1609929X08_3-15.qxp_D-tect150 3/20/15 10:53 AM Page 6
Read all instructions. Failure to follow all instructions listed below may result in electric
shock, fire and/or serious injury.
The detector's ability to detect objects is affected by the proximity of other equipment
that produce strong magnetic or electromagnetic fields, and by moisture, metallic
building materials, foil-laminated insulation materials and/or conductive wallpaper. WARNING
The detector's ability to detect wood substructures (studs) is also affected by inconsistency on the
thickness of the surface material, such as plaster and lath.
It is possible that there may be metal, wood or wiring or something else, such as plastic pipes, beneath
the scanned surface that is not detected.
The detector alone should not be relied on exclusively to locate items below the
scanned surface. Use other information sources to help locate items before
WARNING
penetrating the surface. Such additional sources include construction plans, visible points of entry of
pipes and wiring into walls, such as in a basement, and standard 16" and 24" stud spacing practices.
Before penetrating a surface (such as with a drill, router, saw or nail), always shut off
the electrical power, gas and water supplies. Cutting, drilling, etc... into these items
WARNING
when operational can result in personal injury.
For technological reasons, the measuring tool cannot ensure 100 % certainty. To
rule out hazards, safeguard yourself each time before drilling, sawing or routing
in walls, ceilings or floors by means of other information sources, such as building plans,
WARNING
pictures from the construction phase, etc. Environmental influences, such as humidity or closeness
to electrical devices, can influence the accuracy of the measuring tool. Surface quality and condition of
the walls (e. g., moisture, metallic building materials, conductive wallpaper, insulation materials, tiles)
as well as the amount, type, size and position of the objects can lead to faulty measuring results.
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B Digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
– Consult the dealer or an experienced radio TV technician for help.
Section 15.525 Coordination requirements.
(a) UWB imaging systems require coordination through the FCC before the equipment may be used.
The operator shall comply with any constraints on equipment usage resulting from this coordination.
(b) The users of UWB imaging devices shall supply operational areas to the FCC Office of Engineering
and Technology, which shall coordinate this information with the Federal Government through the
National Telecommunications and Information Administration. The information provided by the UWB
operator shall include the name, address and other pertinent contact information of the user, the desired
geographical area(s) of operation, and the FCC ID number and other nomenclature of the UWB device.
If the imaging device is intended to be used for mobile applications, the geographical area(s) of operation
may be the state(s) or county(ies) in which the equipment will be operated. The operator of an imaging
system used for fixed operation shall supply a specific geographical location or the address at which
the equipment will be

General Safety Rules

SAVE THESE INSTRUCTIONS
operated. This material shall be submitted to the following address:
-6-