Baby auto biro fix Manual De Uso página 11

2. VeHicle installation Points
WHERE:
In the vehicle rear seats.
Please, do NOT install the safety seat in forward seats except for the
following cases:
1. whenever the vehicle does not count with rear seats.
2. when all rear seats are already occupied by children exceeding 135 cm height.
3. when it is not possible to install all child restraints systems in the rear seats.
*Note: According to Spanish legislation for child restraint systems (Royal Decree 667/2015).
HOW:
GROUP 0+ / Install rearward facing.
GROUP 1 / Install forward facing.
GROUP 2 / Install forward facing.
NOTICE:
The child seat must only be used in this seat IF it has a lap and diagonal
belt (3 points).
3. installinG tHe car seat. GrouP 0+
notice
GROUP 0+ only. 0 to 12 months approx. (0-13 Kg)
1. Check the seat is ready to be installed rearward facing (Group 0+)
as shown in fig. 3.3. For this, recline the seat fully. Pull the lever
(G) forward and adjust the angle of recline to position 4 without
releasing the lever. if it is necessary swivel the seat 180º to place the
seat in the opposite direction of travel (fig. 3.2). Release the lever
when the seat is in the desired position.
2. Locate the isoclick Fix® arms
3. Place the seat in the back seat of the vehicle in the opposite
direction of travel.
4. Hold the safety seat with both hands and insert the two isoclick Fix®
(n)
arms firmly into the vehicle´s isofix anchoring points until they
fasten with a click on both sides. The red button will change to green
on both sides (fig. 3.4).
5. Shake the seat to check that it is correctly anchored to the vehicle's
iSoFiX points.
20
(n) in the base of the seat (fig. 3.3).
6. Pass the vehicle seat belt through the slots
support of the safety seat and buckle the vehicle seat belt until you
hear a click (fig. 3.5).
7. Take up the remaining slack of the diagonal section of the 3-point seat
belt (fig. 3.6). and make sure it is as tight fitting as possible. Ensure the
straps are not twisted or knotted at any point
1
uninstalling the isoclick fix® system
1. To free the isoclick Fix® anchoring, press backwards the isoclick Fix
system unlock buttons (the indicator will change from green to red
color), in order to free the seat from the vehicle iSoFiX anchoring
system (fig. 6.7 and 6.8)
4. PlacinG tHe cHild in tHe seat. GrouP 0+
Proper adjustment of the height of the harness ensures the child will be
seated correctly. The harness should be adjusted to the height of the
child's shoulder or slightly above; never behind the child's back or level
with the ears (fig. 4.1).
1. Loosen the harness straps by pulling them gently while pressing the
harness adjustment button
2
straps. Not the shoulder pads.
2. open the buckle
make it easier to seat the child (fig. 4.3).
3. Place the child in the seat.
4. Secure the child in the harness by joining the two parts of the clasp
and fastening the buckle
5. Gently pull the harness adjustment strap to achieve the correct
tension (f) (fig. 4.5). Remember that in order to ensure the child's
safety the harnesses should fit tightly.
5. adJustinG tHe Headrest in HeiGHt
Proper adjustment of the height of the headrest ensures the child will
be seated correctly. The headrest should be adjusted to ensure that the
harness straps (b)
slightly above; never behind the child's back or level with the ears (fig. 4.1).
1. Loosen the harness straps
harness adjustment button
straps. Not the shoulder pads.
2. Adjust the headrest according to the child´s height by pulling the
headrest height regulator
child´s shoulder or slightly above (fig. 5.2).
(e) (fig. 4.2). Tip: only pull on the harness
(d) and place the harness straps on the sides to
(d) until you hear a click (fig. 4.4).
should be adjusted to the height of the child's shoulder or
(b) by pulling them gently while pressing the
(e) (fig. 5.1). Tip: only pull on the harness
(a) adjusting the harness to the height of the
(k) on the security
21