Front Wheels; Stopping The Machine; Parking; Routine Maintenance - breviglieri Zappatrice b60pl Instrucciones De Empleo Y Mantenimiento

The gearbox must only be adjusted or inspected with the ma-
chine unhitched from the tractor or with the tractor engine off and
the machine resting on the ground.

4.8 FRONT WHEELS

On request, the machine can be supplied with front wheels for
depth adjustment purposes. The adjustments are made by loos-
ening the screw (A Fig. 8) and lowering or raising the wheel. In
the former case, the depth becomes more shallow while in the
latter case it increases. Always remember to tighten the lock nut
sufficiently.
If the wheels are supplied separately, comply with the following
instructions to mount them on the machine:
- Mount the wheel support on the square section front tube and
fix it in place with the supplied U-bolts, taking care to tighten the
relative nuts to the correct extent.
When you remove the wheels, keep the side skids fully raised
since in this case, they only act as a protection.

4.9 STOPPING THE MACHINE

At the end of the job, the operator must:
- Disengage the tractor PTO.
- Lower the machine to the ground by means of the power lift.
- Stop the tractor and engage the parking brake.
- Make sure that all parts of the machine are at a standstill.
Only after the above mentioned operations have been carried out
may the operator leave the tractor unattended.

4.9.1 PARKING

- At the end of the job, the machine must be parked on a flat,
suitable surface.
- Stop the tractor and apply the parking brake.
- With the tractor stopped and all components at a complete stand-
still, remove the driveline from the PTO of the tractor.
- Unhitched the machine from the tractor.
WARNING
The place in which the machine is parked must be:
- Dry.
- Sheltered from adverse weather conditions.
- Guarded or locked up to prevent children or unauthorized
persons from freely accessing the machine.
If the machine is to remain idle for a long period of time, lu-
bricate the parts subject to wear and store the machine in a
dry, sheltered place, covered with a plastic sheet.
This will ensure that the machine is in the ideal condition
when required again.
CAUTION
b60pl
SECTION 5
Maintenance

5.1 ROUTINE MAINTENANCE

The various routine maintenance operations are described be-
low. Remember that lower running costs and longer machine life
depend on continual compliance with these instructions.
Before proceeding with any operation, make sure that the
machine is parked on a flat surface. Prevent it from moving
by placing chocks under the wheels.
Servicing, adjusting and the operations required to prepare
the machine for work must be carried out with the tractor
and the driveline detached from the machine.
The servicing frequencies indicated in this manual are in-
dicative and refer to normal conditions of use. They may there-
fore vary depending on the type of service, whether the envi-
ronment is dirty or not, seasonal factors, etc. The servicing
operations must obviously be carried out more frequently in
heavier duty service conditions.
- Before injecting lubricating grease into the grease nipples,
carefully clean these latter to prevent mud, dust or foreign
bodies from mixing with the grease as this would reduce
or even annul its lubricating effects.
Injection into the greasing points of a large quantity of
grease at high pressure can damage the bearing protec-
tion. This operation must therefore be carried out with the
greatest care.
- Lubricate and grease all the required points, including the
chains.
- Use oil of the recommended type for topping up and
changes.
Keep all lubricants well away from children's reach.
Carefully read the warnings and precautions on the lubricant
containers.
The operator should thoroughly wash himself after using lu-
bricants.
Dispose of used oil in compliance with the anti-pollution laws.

5.2 LUBRICATION

Lubrication of any machine with parts that turn and/or rub together
is a vitally important task for the life and functionality of the actual
machine itself.
Lubrication must therefore be carried out systematically and at
the required intervals.
The frequencies given refer to machine use in a normal environ-
ment.
If this machine is used in heavier duty conditions, it must naturally
be lubricated more frequently.
- 22 -
WARNING
CAUTION
DANGER