Disposal Of Waste Products; Information Needed By User; Troubleshooting; Maintenance Of The Product - Jacto XP-12 Manual Del Operador

4.7. Disposal of waste products

The elimination of waste resulting from the dismantling of
equipment during service, maintenance or end of life (disposal)
should be carried out respecting the environment, preventing
pollution of air, soil and water. If necessary, the waste should be
stored in appropriate locations and then transported by quali-
fied and trained people and companies.
Disposal of used sprayer should be done at appropriate points
and approved for receiving such material. If there isn't an appro-
priate nearby site, please contact the Customer attendance: Dr.
Luiz Miranda, 1650, 17580-000 – Pompeia – SP – Brazil. Phone:
+55 14 3405 2113. Email: assistencia.tecnicajsfs@jacto.com.br
Opening Hours: Monday to Friday 7:00am to 11:30am and
13:00pm to 17:18pm (Brazilian time zone).

5. Information Needed by User

5.1. Troubleshooting

• Put about 2 liters of water in the tank.
• While operating the lever, look into the tank to see how the
problem arises.
• Refer to the table and diagram below.
DESCRIPTION
Leakage through the cylinder upper part.
After pumping and
pressurizing the chamber, as you operate
the lever it drops fast. due to wear or impurities.
After pumping and
pressurizing the chamber, the lever rises
quickly when released. due to wear or impurities.
12/68
CAUSES CORRECTIONS
Worn or dried out Replace or lubricate
piston cup. the pump.
Cylinder valve
Clean or replace
not sealing properly
the valve.
Chamber valve
Clean or replace
not sealing properly
the valve.

5.2. Maintenance of the product

Every 40 hours, clean the chamber and lubricate all the com-
ponents. Use a pliers to disassemble the parts and a brush with
nylon bristles clean and neutral detergent. Always use personal
protective equipment (PPE).

5.3. Cleaning the sprayer

After finishing the spray application, clean and wash all equip-
ment in an approved decontamination area.
Operate the lever for the internal cleaning of the camera.
Remove the chamber and lubricate the piston.

5.4. Drainage

You must drain it when you finish the use.

5.5. The consequences of improper service

Do not change the sprayer components. Always check for leaks
or malfunction. Follow the maintenance instructions and use
original parts provided by Jacto.
Failure to follow the instructions may cause damage to the oper-
ator's health and the environment.
5.5a. In case of clogged nozzle
Clean nozzles and filters Clean nozzles with brush
Do not use metal instruments. Use a brush with nylon bristles
clean and neutral detergent.
5.6. Cylinder maintenance
• Remove the pumping rod from the chamber. Loosen the gas-
ket holder and remove the assembly;
• Remove the chamber (A) from the cylinder (B). Clean the ball
(C) and the piston cup (D); replace them if necessary.
C
A
B
D
5.7. Triple rinse of empty agrochemicals
containers
NOTICE: Even the containers considered empty contain chemi-
cal residues. Therefore, discarding the containers without wash-
ing out the residues is extremely dangerous to man, animals and
environment. In the case of metal, plastic and glass chemical
containers, each container must be rinsed three times to ensure
the residues are completely removed. This manual describes
how to make the triple rinse in a correct, safe and effective way.
1. Immediately after emptying the container, you must keep
it with the opening upside down over the sprayer tank
opening or over the bucket that you are using to prepare
the chemical mixture for at least 30 seconds, until no res-
idue is left in the container, when the drops are falling in
long intervals.
2. Hold the container in the upright position and fill it with
water up to 1/4. For example: in a 1000 ml container, put
250 ml of water.
13/68